AVSPARE.COM
parts catalog

RING 4644994 - Caterpillar



4644994 RING Caterpillar parts RING
Rating:
51
Alternative (cross code) number:
CA4644994
464-4994
4644994
Caterpillar 4644994 RING
Weight: 12 pounds 5 kg.

Buy RING 4644994 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Valve Calibration
In order to ensure proper performance of the hydraulic system on the machine, the valves must be calibrated.If this procedure was not completed during the initial installation of the AccuGrade Laser system, Refer to Testing and Adjusting, "Bank Valve (Grade Control) - Calibrate".If the valve calibration has been previously completed, press the Arrow keys in order to scroll to the next menu.Customize the AccuGrade Laser System
The menu for "Customize" is located within the "Configuration" menu. The menu allows the user to customize the AccuGrade Laser with the items in the following menus:Select the Operating Mode
Press the Arrow keys until "Customize" is highlighted on the Display.
Illustration 4 g01306926
Press the "OK/right reset" key in order to access the "Customize" menu. A screen that is similar to Illustration 4 appears.
Illustration 5 g01309893
Display screen for Dual Mast system
Illustration 6 g01301951
Display screen for Single Mast system
Press the "OK/right reset" key in order to access the "Operating Mode" menu. A screen that is similar to Illustration 5 appears for the Dual Mast System. A screen that is similar to Illustration 6 appears for the Single Mast System.
Press the Arrow keys until the mode that is required is highlighted on the Display.
Press the "OK/right reset" key in order to save the changes and return to the "Customize" menu.In order to exit back to the "Customize" menu without saving any changes, press the "ESC/left reset" key.Set The Elevation Offset
The "Elevation Offset" menu allows you to set the amount each toggle of the Elevation Offset switch on the remote switch assembly increases or decreases the reference elevation. This allows you to move the blade a certain distance in the upward or downward direction with the toggle of a switch.
Press the Arrow keys until "Elevation Offset" is highlighted on the display.
Illustration 7 g01299822
Press the "OK/right reset" key in order to access the "Elevation Offset" menu. A screen that is similar to Illustration 7 appears.
Press the "Increment" key in order to move the cursor. This allows the user to highlight the digit.
In order to edit the "elevation offset increment", perform one of the following procedures that is listed below:
Press the "ESC/left reset" key and the "OK/right reset" key simultaneously in order to reset the elevation offset to 0.030 m (0.1 ft).
Press the "Increment" key in order to move the cursor to the right and highlight the digit that needs to be changed.Press the Arrow keys UP in order to increase the highlighted value.Press the Arrow keys DOWN in order to decrease the highlighted value.
When the required elevation offset is entered, press the "OK/right reset" key in order to return to the "Customize" menu.In order to exit back to the "Customize" menu without saving any changes, press the "ESC/left reset" key.
Illustration 8 g01322204
Guidance screen for Dual Mast system
Illustration 9 g01301820
Guidance screen for Single Mast system
Press the "Menu" key in order to return to Guidance mode.A screen that is similar to Illustration 8 will be shown for the Dual Mast system.A screen that is similar to Illustration 9 will be shown for the Single Mast system.Configuring


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.