AVSPARE.COM
parts catalog

RING 4646316 - Caterpillar



4646316 RING Caterpillar parts RING
Rating:
36
Alternative (cross code) number:
CA4646316
464-6316
4646316
Caterpillar 4646316 RING
Weight: 11 pounds 5 kg.

Buy RING 4646316 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Winch Pressure Sensor
Illustration 6 g01337661
When the winch is in the brake mode, very little pressure should be present in the drive loop. After the brake for the winch is applied, the sensor determines if high pressure is in the line. The sensor allows the ECM to determine the pressure differential across the motor ports of the winch.Switches
Implement Lockout
Illustration 7 g01113796
The implement lockout switch is designed to de-energize the implement lockout solenoid. The ECM will provide power to the solenoid. The switch is a two parity switch. The ECM disengages the implement lockout solenoid when the switch is placed in the LOCKED position. The switch should be in the LOCKED position before any of the following conditions occur:
The operator exits the machine.
The machine is serviced.
The machine is left unattended.The switch affects the system in the following manner:LOCKED - The implement lockout solenoid is de-energized. The implement system is no longer operable.UNLOCKED - The implement lockout solenoid is energized. The implement system is enabled.The switch is a double-pole switch. The switch has a normally closed contact and a normally open contact. The ECM can always determine whether the switch is in the LOCKED position or the UNLOCKED position. The two input circuits are used for diagnostic purposes. The ECM will detect a failure in the circuit if the two circuits of the switch are ever in the same state. The ECM will also record a diagnostic code. The diagnostic code that is associated with the implement lockout switch is CID 0490.Fourth Function
Illustration 8 g01337662
The switch is two directional. The switch has three pins that connect to the ECM. The fourth function is normally controlled by the lever. The use of this switch allows the lever to be used for a separate function. This switch could be used in order to operate the fire plow. Depressing and holding the switch in one direction actuates the raise solenoid for the fourth function. Holding the switch in the other direction actuates the lower solenoid for the fourth function. This switch allows control of the fourth function.Blade Mode (Auto/Manual) with AccuGrade System
Illustration 9 g01338185
If the AccuGrade System option is installed, the left yellow button (1) changes the AccuGrade System control. Push button (1) in order to change between auto control and manual control. If the AccuGrade System option is active, press button (2) in order to increment and press button (3) in order to decrement.At any time, the operator can select the manual mode or the automatic mode by pressing the left yellow button on the blade control handle. In addition, the current mode is displayed for the operator on the display module.Winch Free Spool
Illustration 10 g01337663
Push the switch in order to release the winch cable. The winch cable unreels by manually pulling the winch cable. Machine or hydraulic assistance is not needed. The winch will remain in the FREE SPOOL position until the switch is pressed again or until any other function of the winch is activated.Note: Activating the switch allows the spool to move without tension


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.