AVSPARE.COM
parts catalog

RING 9W0055 - Caterpillar



9W0055 RING Caterpillar parts 950B, D250E, D300E RING
Rating:
33
Alternative (cross code) number:
CA9W0055
9W-0055
9W0055
Caterpillar 9W0055 RING
Weight: 0.50 pounds 0 kg.

Buy RING 9W0055 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK, WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
3N0759 - Ring (Part of 5P374 Group) 9W0055 for Caterpillar (CAT)
$20.62

26 Jan 2022

US: Florida-Parts-Zone
3N0759 - Ring (Part of 5P374 Group) 9W0055 for Caterpillar (CAT)
FIRST PRICE PARTS
3N0759 Seal O Ring Fits Caterpillar 9W0055 725 730 D250E II D300E II D250E D300E
$14.10

11 May 2022
0.39[0.18] Pounds
US: ProperBuy
3N0759 Seal O Ring Fits Caterpillar 9W0055 725 730 D250E II D300E II D250E D300E
TCP Warranty
Number on catalog scheme:
 
  For full view, you need register

Compatible equipment models: 9W0055:

ARTICULATED TRUCK  D250E   D300E  
WHEEL LOADER  950B   Caterpillar

Information:

If the turbocharger has unusual noise or vibrations, inspect the turbocharger.If the turbocharger fails during engine operation, damage to the turbocharger compressor wheel and/or to the engine may occur. Damage to the turbocharger compressor wheel could allow parts from the compressor wheel to enter an engine cylinder. This can cause additional damage to the pistons, the valves, and the cylinder head.
Turbocharger bearing failures can cause large quantities of oil to enter the air inlet and exhaust systems. Loss of engine lubricant can result in serious engine damage.Minor leakage of a turbocharger housing under extended low idle operation should not cause problems as long as a turbocharger bearing failure has not occurred.When a turbocharger bearing failure is accompanied by a significant engine performance loss (exhaust smoke or engine rpm up at no load), do not continue engine operation until the turbocharger is repaired or replaced.
An inspection of the turbocharger can minimize unscheduled downtime. Also, the chance for potential damage to other engine parts is reduced.Note: Turbocharger components require clearances that are precise. The turbocharger cartridge must be balanced due to high rpm.The following conditions can cause the turbocharger to be out-of-balance:
The buildup of deposits
Chipping and/or flaking of depositsIf the turbocharger must be removed for inspection, use caution. Do not remove deposits from the turbine wheel. Do not attempt to clean the turbine wheel. For service information, refer to Disassembly and Assembly and Specifications. For options regarding repair and replacement, consult your Caterpillar dealer.
Remove the exhaust outlet piping and remove the air inlet piping from the turbocharger. Visually inspect the piping for the presence of oil.
Turn the compressor wheel and the turbine wheel by hand. The assembly must turn freely. Inspect the compressor wheel and the turbine wheel for contact with the turbocharger housing. There must not be any visible signs of contact between the turbine wheel or compressor wheel and the turbocharger housing. If there is any indication of contact, recondition the turbocharger.
Check the compressor wheel for cleanliness. Look for evidence of dirt and/or moisture that is passing through the air filtering system. If oil is found, there is a possibility of a failed turbocharger oil seal.The presence of oil may be the result of extended engine operation at low idle. The presence of oil may also result from restriction of the inlet air that causes the seals to leak.Note: Deposits of ash and silicone can accumulate on the turbine wheel. Turbine wheel will become unbalanced when the deposits flake off. The turbocharger cartridge must be replaced when this occurs. However, remove deposits from the housing. This will prevent wear on the blades of the new turbine wheel.
Inspect the turbine wheel and the nozzle for deposits of ash and silicone. If deposits of 1.6 mm (0.06 inch) thickness are found or if the turbine is in contact with the housing, the turbocharger must be serviced by the OEM of the turbocharger. For options regarding repair and replacement, consult your Caterpillar dealer.
Inspect the bore of the turbine housing for corrosion

Caterpillar parts catalog:

Caterpillar parts catalog
D250E Articulated Truck 5TN00001-UP (MACHINE) POWERED BY 3306 Engine
D300E Articulated Truck 7FN00001-UP (MACHINE) POWERED BY 3306 Engine
950E WHEEL LOADER 65R03089-UP (MACHINE) POWERED BY 3304 ENGINE


Parts ring Caterpillar catalog:

1982640 RING
322C, 345C, 834G, 966H
0665816 RING-RETAINING
735, 735B, 740, 740B, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
8E3839 RING-SEAL
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
1272936 RING-ADJUSTING
789B, 789C, 789D, 793B, 793C
1172991 RING-ADJUSTING
784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C
6G7038 RING-SEAL
776C, 777B, 777D, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 795F AC
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.