AVSPARE.COM
parts catalog

RING 9W0218 - Caterpillar



9W0218 RING Caterpillar parts RING
Rating:
26
Alternative (cross code) number:
CA9W0218
9W-0218
9W0218
Caterpillar 9W0218 RING
Weight: 13 pounds 6 kg.

Buy RING 9W0218 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


To prevent a bent shaft, do not put a side force on the turbine shaft when the compressor wheel nut is loosened.
5. Put the end of the turbine shaft in tooling (B). Use a universal joint and socket of the correct size to remove the nut that holds compressor wheel (7) on the turbine shaft 6. Use a press and push the turbine shaft out of compressor wheel (7) and the cartridge housing. Remove compressor wheel (7) from the cartridge housing. 7. Remove shroud (9) from turbine shaft (8). 8. Remove seal ring (10) from turbine shaft (8). 9. Bend the tabs of the locks from bolts (11) and remove the bolts.10. Remove backplate assembly (12) from the cartridge housing. Make a note of the position of the oil holes in the backplate assembly and cartridge housing for correct alignment at assembly. 11. Push spacer (13) out of the bore in backplate (12). 12. Remove seal rings (14) from spacer (13). 13. Remove seal (15) from the cartridge housing. 14. Remove thrust collar (16) from the cartridge housing. 15. Remove thrust bearing (17) from the cartridge housing. If the bearings are to be used again, put identification on them, as to their location, for correct assembly.16. Remove bearing (18) from the cartridge housing. 17. Remove washer (19) from the cartridge housing. 18. Remove snap rings (20) and (21) with tooling (C). 19. Remove bearing (22) from the cartridge housing. 20. Remove washer (23) from the cartridge housing. 21. Remove snap ring (24) from the cartridge housing with tooling (C). 22. Turn the cartridge housing over. Remove plates (25) from the cartridge housing.Assemble Turbocharger
1. Make sure all of the oil passages in the turbocharger cartridge housing, backplate assembly and bearings are clean and free of dirt and foreign material.2. Put clean engine oil on all parts of the cartridge at assembly. 3. Install plates (25) on the cartridge housing. Turn the cartridge housing over. Make sure the round edge on the outside diameter of the snap ring is toward the bearing when the snap rings are installed.4. Install snap ring (24) in the turbine end of the cartridge housing with tool (A). Install washer (23) and bearing (22). 5. Install snap ring (21) in the cartridge housing with tool (A) to hold the washer and bearing in place. 6. Install snap ring (20) in the cartridge housing with tool (A).7. Install washer (19) and bearing (18) in the cartridge housing until washer (19) makes contact with snap ring (20). 8. Install thrust bearing (17) over the dowels in the cartridge housing. Make sure the grooves in bearing (17) are toward the outside as shown. 9. Put thrust collar (16) in position on the thrust bearing with the counterbore for the spacer up. 10. Install seal ring (15) in the groove of the cartridge housing. 11. Install seal rings (14) on spacer (13) so the gaps in the seal rings are 180° apart. 12. Install spacer (13) in backplate


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.