AVSPARE.COM
parts catalog

RIVET 0005614 - Caterpillar



0005614 RIVET Caterpillar parts RIVET
Rating:
56
Alternative (cross code) number:
CA0005614
000-5614
0005614
Caterpillar 0005614 RIVET
Weight: 0.01 pounds 0 kg.

Buy RIVET 0005614 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
ZZ 6V-9830 Cap As 2
6V-9509 Face Seal Plug 2
6V-9829 Cap As 2
6V-9508 Face Seal Plug 2
6V-9831 Cap As 1
6V-9510 Face Seal Plug 1 Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the hydraulic tank into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change". Note: In addition to the weight of the bottom guard, bottom guards may contain approximately 90 kg (200 lb) of the following objects: loose bolts, tools, rocks, dirt, liquids and debris.
Illustration 1 g00853562
Use Tooling (A) to support middle bottom guard (1). The weight of the middle bottom guard is approximately 35 kg (77 lb). Remove the bolts and middle bottom guard (1).
Illustration 2 g00854536
Illustration 2 is from the underside of the machine.
Remove hose assemblies (1), (3), and (5) from valve block (6). Remove hose assemblies (2) and (4) from valve block (6).
Illustration 3 g00854619
Illustration 3 is from the underside of the machine.
Disconnect harness assemblies (7).
Remove bolts (8), the washers, and the clips and remove valve block (6).
Illustration 4 g01051184
Remove nut (9) and washer (10). Remove coil assembly (11).
Remove cartridge assembly (12).
Illustration 5 g00855330
Remove backup ring (13) and O-ring seal (14) from valve assembly (12). Remove backup ring (15) and O-ring seal (16) from the valve assembly. Remove O-ring seal (17) from the cartridge assembly.
Illustration 6 g01051178
Remove nut (19) and washer (20) and remove coil assembly (21).
Remove cartridge assembly (18).
Illustration 7 g00855395
Remove O-ring seals (25), (24), (23), and (22) from cartridge assembly (18).
Remove backup rings (26), (27), and (28) from the cartridge assembly.
Illustration 8 g00855408
Remove remaining plugs (29). Each plug has an O-ring seal. Inspect the O-ring seals for damage or for wear. Replace the O-ring seals, if necessary.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.