parts catalog

ROPE-WIRE 5087914 - Caterpillar

5087914 ROPE-WIRE Caterpillar parts ROPE
Alternative (cross code) number:
Caterpillar 5087914 ROPE-WIRE
Weight: 1 pounds 0 kg.

Buy ROPE-WIRE 5087914 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Illustration 1 g01216611
Schematic of the Hoe Auxiliary Valve #2 Port A SolenoidThis diagnostic code is associated with the Hoe Auxiliary Valve #2 Port A Solenoid. The FMI 06 means that the ECM has determined that there is a short to ground in the circuit. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2244 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. System Response:
The system will not initialize after power is cycled.
The hydraulic functions for the extend, retract, reverse and forward are lost after power is cycled.
There will be no effect to the systems after powerup until the next reset of the valve ECM.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:CID 2244 FMI 06 changes to CID 2244 FMI 05 when the solenoid is disconnected.Results:
YES - CID 2244 FMI 06 changes to CID 2244 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - CID 2244 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the machine ECM.
At the machine harness connector, measure the resistance from the signal contact 6 (wire K766-PK) to all contacts that are used in the machine harness connectors for the machine ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between contact J1-61 (wire K766-PK) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts

Parts rope Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.