3843522 SCREEN AS Caterpillar parts
320E, 320E L, 320E LN, 323E L
Rating:
Alternative (cross code) number:
CA3843522
384-3522
3843522
CA3843522
384-3522
3843522
Weight: 4 pounds 1 kg.
EXCAVATOR,
Number on catalog scheme:
3
For full view, you need register
Information:
9. Remove bracket assembly (16) and link (17). 10. Put identification marks on fuel racks (18) and (19), and remove the fuel racks. 11. Put identification marks on each spacer (20) and lifter (21) so they can be installed in their original position. 12. Remove fuel injection pump camshaft (22) from the pump housing.13. Remove O-ring seal (23). 14. Inspect link pivot shaft (24) and bracket locating pin (25). Make a replacement by removal of shaft (24) and dowel (25) with tool (D). 15. Inspect upper bearing (26) and the lower bearing that hold the pinion gear in the pump housing.16. Make a replacement of bearings (26) if necessary.17. Inspect idler gear shaft (27). If a replacement is necessary, remove the shaft with tooling (D). 18. Inspect fuel rack bearings (28) and camshaft bearings (29). If a replacement is necessary, remove bearings (28) and (29).19. Use tool group (E) to remove bearings (28). 20. Remove regulator valve (30). 21. Remove pin (31) to disassemble the regulator valve, and inspect the components.22. Piston (32) must move freely in valve body (30).23. Make a reference to the Specifications for spring (34).24. Make a replacement of O-ring seals (33).Assemble Fuel Injection Pump Housing
Pin (2) must not extend out of either side of valve body (3).
1. Install spring (4), piston (1) and pin (2) in valve body (3).2. Put clean engine oil on the valve body and O-ring seals (5). Install the oil bypass valve in the pump housing. Tighten the bypass valve body to a torque of 68 14 N m (50 10 lb.ft.). 3. Install the camshaft front and rear bearings with tool group (A). Install the front bearing until it is a distance of 1.0 0.5 mm (.04 .02 in.) from the front surface of the pump housing. Make sure both oil holes in bearing are in alignment with the oil holes in the pump housing. 4. Put tool (B) in the fuel pump housing with the dowels of tool (B) in alignment with the left fuel rack bore. Install the bolt that holds the tool in place on the housing.5. Put a new bearing in position with the tab of the bearing up. Install the bearing with tool (C) until the shoulder of tool (C) makes contact with tool (B).6. Turn tool (B), and make an alignment of the dowels on tool (B) with the right fuel rack bore.7. Do Step 3 again for the left fuel rack bearing. 8. Install shaft (6) to a height of 16.8 0.5 mm (.66 .02 in.) 9. Make sure the chamfer on the lower bearing for the pinion gear is toward the inside and the notch is in the location shown. Install the bearing 28.4 0.5 mm (1.12 .02 in.) below the bearing bore surface with tooling (D).10. Make sure the chamfer on the upper bearing for the pinion gear is toward the inside and the notch is in the location shown.
Pin (2) must not extend out of either side of valve body (3).
1. Install spring (4), piston (1) and pin (2) in valve body (3).2. Put clean engine oil on the valve body and O-ring seals (5). Install the oil bypass valve in the pump housing. Tighten the bypass valve body to a torque of 68 14 N m (50 10 lb.ft.). 3. Install the camshaft front and rear bearings with tool group (A). Install the front bearing until it is a distance of 1.0 0.5 mm (.04 .02 in.) from the front surface of the pump housing. Make sure both oil holes in bearing are in alignment with the oil holes in the pump housing. 4. Put tool (B) in the fuel pump housing with the dowels of tool (B) in alignment with the left fuel rack bore. Install the bolt that holds the tool in place on the housing.5. Put a new bearing in position with the tab of the bearing up. Install the bearing with tool (C) until the shoulder of tool (C) makes contact with tool (B).6. Turn tool (B), and make an alignment of the dowels on tool (B) with the right fuel rack bore.7. Do Step 3 again for the left fuel rack bearing. 8. Install shaft (6) to a height of 16.8 0.5 mm (.66 .02 in.) 9. Make sure the chamfer on the lower bearing for the pinion gear is toward the inside and the notch is in the location shown. Install the bearing 28.4 0.5 mm (1.12 .02 in.) below the bearing bore surface with tooling (D).10. Make sure the chamfer on the upper bearing for the pinion gear is toward the inside and the notch is in the location shown.
Caterpillar parts catalog:
Parts screen Caterpillar catalog:
3361150
SCREEN GP-SUN
311D LRR, 312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L...
311D LRR, 312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L...
3755636
SCREEN GP
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L
3531858
SCREEN GP-SUN
323E L, 324D L, 324E, 324E LN, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D L, 336D LN, 336D2, 336E, 336E H, 336E LH, 336E LN, 345D, 345D L, 349E, 349E L VG, 374F L, 390F L
323E L, 324D L, 324E, 324E LN, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D L, 336D LN, 336D2, 336E, 336E H, 336E LH, 336E LN, 345D, 345D L, 349E, 349E L VG, 374F L, 390F L
3264408
SCREEN GP-HYDRAULIC
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 568 FM LL
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 568 FM LL
1195398
SCREEN-FILTER
312C, 312C L, 315C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR,...
312C, 312C L, 315C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR,...
318C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D...
3361151
SCREEN AS
311D LRR, 312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L...
311D LRR, 312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L...
3843521
SCREEN AS
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L
3843523
SCREEN AS
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L