3844321 SCREEN AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA3844321
384-4321
3844321
CA3844321
384-4321
3844321
For full view, you need register
Information:
Low Voltage
Illustration 1 g00845479
Motor Contactors (1) Motor contactor for the crankcase breather (gas engine only) (2) 100 hp motor control starter for the radiator fan (3516B engines only) (3) Auxiliary contacts for the contactor for the fan motor (4) Overload relay for the crankcase breather motor contactor (heater type relay) (5) Overload relay for the contactor for the fan motor (heater type relay)The motor contactor for the crankcase breather (1) is optional equipment for gas engines. This motor contactor is used only on gas engines.Motor contactors are equipped with thermal type overloads. These thermal type overloads protect against the following failures: motor, cables for the motor and switchgear. The thermal type overloads have a factory preset value for overcurrent. If the overload trips the overload must be manually reset.
The motor starter compartment should not be accessed unless the equipment is de-energized. Personal injury and/or damage to the switchgear could occur if the motor starter compartment is accessed when the equipment is energized. Do not operate the power module if the cover for the motor starter compartment is not installed. Ensure that the cover for the motor starter compartment is installed. Bodily contact with electrical potential will cause personal injury or death.
Medium Voltage
Illustration 2 g00850969
Motor Contactor (6) Motor fuses (5 kV) (7) Vacuum interrupter/contactor (5 kV) (8) Door operated safety switch (9) Metallic guard (not shown) (10) Terminal board and circuit boardA metallic guard (9) attaches with six bolts in order to enclose the 5 kV equipment.
The metallic guard is installed on the equipment before the equipment is shipped. Do not operate the equipment if the metallic guard is not properly installed. Use the bolts that are provided in order to reinstall the metallic guard if the guard is removed. Operating the equipment without the metallic guard installed may result in personal injury or death by electrocution. Bodily contact with electrical potential will cause personal injury or death.
Note: The door operated safety switch (8) is the limit switch for the left top door. The door operated safety switch trips the generator circuit breaker and the door operated safety switch commands the genset to shut down.
Illustration 1 g00845479
Motor Contactors (1) Motor contactor for the crankcase breather (gas engine only) (2) 100 hp motor control starter for the radiator fan (3516B engines only) (3) Auxiliary contacts for the contactor for the fan motor (4) Overload relay for the crankcase breather motor contactor (heater type relay) (5) Overload relay for the contactor for the fan motor (heater type relay)The motor contactor for the crankcase breather (1) is optional equipment for gas engines. This motor contactor is used only on gas engines.Motor contactors are equipped with thermal type overloads. These thermal type overloads protect against the following failures: motor, cables for the motor and switchgear. The thermal type overloads have a factory preset value for overcurrent. If the overload trips the overload must be manually reset.
The motor starter compartment should not be accessed unless the equipment is de-energized. Personal injury and/or damage to the switchgear could occur if the motor starter compartment is accessed when the equipment is energized. Do not operate the power module if the cover for the motor starter compartment is not installed. Ensure that the cover for the motor starter compartment is installed. Bodily contact with electrical potential will cause personal injury or death.
Medium Voltage
Illustration 2 g00850969
Motor Contactor (6) Motor fuses (5 kV) (7) Vacuum interrupter/contactor (5 kV) (8) Door operated safety switch (9) Metallic guard (not shown) (10) Terminal board and circuit boardA metallic guard (9) attaches with six bolts in order to enclose the 5 kV equipment.
The metallic guard is installed on the equipment before the equipment is shipped. Do not operate the equipment if the metallic guard is not properly installed. Use the bolts that are provided in order to reinstall the metallic guard if the guard is removed. Operating the equipment without the metallic guard installed may result in personal injury or death by electrocution. Bodily contact with electrical potential will cause personal injury or death.
Note: The door operated safety switch (8) is the limit switch for the left top door. The door operated safety switch trips the generator circuit breaker and the door operated safety switch commands the genset to shut down.