AVSPARE.COM
parts catalog

SCREW SC1692 - Caterpillar



SC1692 SCREW Caterpillar parts D7G SCREW
Rating:
38
Alternative (cross code) number:
CASC1692
SC-1692
SC1692
Caterpillar SC1692 SCREW

Buy SCREW SC1692 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: SC1692:

TRACK-TYPE TRACTOR  D7G   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
4360-16 E946 (2) Aftertreatment #1 SCR Catalyst Intake Gas Temperature : High - moderate severity (2) The aftertreatment SCR catalyst intake gas temperature sensor has detected that the SCR intake temperature is above the normal operating range.
4360-17 E947 (1) Aftertreatment #1 SCR Catalyst Intake Gas Temperature : Low - least severe (1) The aftertreatment SCR catalyst intake gas temperature sensor has detected that the SCR intake temperature is below the normal operating range.
4360-18 E947 (2) Aftertreatment #1 SCR Catalyst Intake Gas Temperature : Low – moderate severity (2) The aftertreatment SCR catalyst intake gas temperature sensor has detected that the SCR intake temperature is far below the normal operating range.
Illustration 1 g03273938
(1) Turbocharger
(2) DPF
(3) SCR inlet
(4) SCR outlet The temperature of the exhaust gas is checked by the SCR inlet temperature sensor (5) at the inlet of the SCR canister (3). This input is used to ensure a proper reaction with the SCR catalyst and to properly dose DEF into the exhaust stream.
Illustration 2 g03273939
(5) SCR inlet temperature sensor
Table 2
Troubleshooting Test Steps Values Results
1. Determine the diagnostic code.
A. Connect Cat® ET to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Determine if a diagnostic trouble code is present.
Diagnostic trouble code
Result : A 4360-16 or E946 (2) code with an ETI of 1 or 2 is active or logged.
Proceed to Test Step 2.
Result : A 4360-17, E947 (1), 4360-18 or E947 (2) code is logged or active.
Proceed to Test Step 2.
2. Check the operation of the SCR catalyst inlet temperature sensor.
Note : Only perform this step on a cold engine.
A. Remove the SCR catalyst inlet temperature sensor and allow the sensor to rest in ambient air for 2 minutes.
B. Connect to the engine ECM by using Cat ET.
C. Monitor the value of the SCR catalyst inlet temperature sensor on Cat ET.
Sensor
Result : The value of the SCR catalyst inlet temperature sensor is within 9° C (15° F) of ambient temperature.
Repair : Reinstall the sensor. torque the sensor to the proper specification.
For a 4360-16 or E946 (2) code proceed to Test Step 4.
For a 4360-17, E947 (1), 4360-18 or E947 (2) code proceed to Test Step 3.
Result : The value of the SCR catalyst inlet temperature sensor is not within 9° C (15° F) of ambient temperature.
Repair : Replace the SCR catalyst inlet temperature sensor. Refer to the Disassembly and Assembly manual for more information.
Proceed to Test Step 5.
3. Check for exhaust leaks.
A. Start the engine.
B. Check the exhaust system for proper installation.
C. Check for proper installation of the exhaust system insulation.
D. Inspect the exhaust system between the DPF and the SCR for signs of an exhaust leak.
E. Inspect the SCR inlet temperature sensor to ensure proper installation in the sensor port.
Exhaust leaks
Result : There were exhaust leaks found.
Repair : Repair or replace the component that is causing an exhaust leak.
Proceed to Test Step 5.
4. Check the Diesel Exhaust Fluid (DEF) quality.
A. Measure the DEF quality. Refer

Caterpillar parts catalog:

Caterpillar parts catalog
D7G TRACTOR 3GF00001-UP (MACHINE)


Parts screw Caterpillar catalog:

9N3388 SCREW-SELF LOCKING-IN 8T4781 HANDLE AS
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 215, 215B, 235, 235B, ...
7B3028 SCREW-DRIVE-SERIAL NUMBER PLATE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14E, 14G, 14H, 14H NA, 16, 160G, 160H, 160H ...
8M3267 SCREW-HEX SOCKET
120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 1673C, 16H, 16H NA, 235, 235B, 24H, ...
5P4939 SCREW-MACHINE
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 215, 225, 225D, 235, 235B, 235D, 245, 312, 3204, 3208, 330, 3...
9X2836 SCREW-BUTTON HEAD
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235B, 245, 3208, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B L,...
3H8389 SCREW-FILLER CAP
12G, 130G, 140G, 14G, 160G, 16G, 227, 229D, 235, 245, 3208, 3304, 3304B, 3306, 3406, 3406B, 3408, 3412, 3412C, 561B, 561D, 572G, 583K, 594, 594H, 613, 615, 621, 621B, 621E, 621R, 623E, 627E, 631E, 637...
4B1223 SCREW-MACHINE
3116, 3406E, 3412E, 5110B, 561D, 571G, 572G, 583K, 594H, 977D, 977L, 983B, 994, C15, C18, C30, C32, C9, D4E, D4E SR, D5B, D5E, D6D, D6E, D6E SR, D7G, D8K, D9H
4B1291 SCREW
140, 153, 1673, 1673B, 173B, 183B, 55, 58, 769, 773, 824, 824B, 834, AP-1050, D10, D10N, D330A, D333A, D342, D4E, D4E SR, D5B, D5E, D6D, D6E, D6E SR, D7G, D7H, D8K, D8L, D9H, D9L, D9N, SCT673
6J5349 SCREW
7A, 7S, D7G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.