AVSPARE.COM
parts catalog

SCREWDRIVER 1C3844 - Caterpillar



1C3844 SCREWDRIVER Caterpillar parts AP-1200, PR-1000, PR-450, PR-750B SCREWDRIVER
Rating:
82
Alternative (cross code) number:
CA1C3844
1C-3844
1C3844
Caterpillar 1C3844 SCREWDRIVER
Weight: 1 pounds 0 kg.

Buy SCREWDRIVER 1C3844 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT PAVER, COLD PLANER,

Compatible equipment models: 1C3844:

ASPHALT PAVER  AP-1200  
COLD PLANER  PR-1000   PR-450   PR-750B   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Start By:
Remove the inlet elbow and inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g02025312
Illustration 2 g02025313
Remove nut (3) from the terminal insulator.
Disconnect wire (4) from the terminal insulator.
Remove nuts (1) that secure busbar (2) to the glow plugs (5).
Remove the busbar from the glow plugs.
Clean the area around the glow plugs. Ensure that the area is free from contamination before removal of the glow plugs.
Remove glow plugs (5) from cylinder head (6). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 247-5377 Torque Wrench 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g02025313
Before installing glow plugs (5), ensure that the glow plugs are operating correctly. Refer to Troubleshooting, "Glow Plug Starting Aid - Test" “Check the Operation of the Glow Plugs” for the correct procedure.
Ensure that the threads of the glow plugs are clean and free from damage. Replace any damaged glow plugs.
Install glow plugs (5) into cylinder head (6). Tighten the glow plugs to a torque of 15 N m (132 lb in).
Illustration 4 g02025312
Position busbar (2) onto the glow plugs. Install nuts (1) onto the glow plugs.
Use Tooling (A) to tighten nuts (1) to a torque of 2 N m (17 lb in).
Connect wire (4) to the stud on the terminal insulator.
Install nut (3) to the stud on the terminal insulator. Tighten the nut to a torque of 6 N m (53 lb in).
Turn the battery disconnect switch to the ON position. End By:
Install the inlet elbow and inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Install" for the correct procedure.

Caterpillar parts catalog:

Caterpillar parts catalog
PR-1000C Cold Planer 5XC00138-UP (MACHINE) POWERED BY 3208 Engine


Parts screwdriver Caterpillar catalog:

2U5063 SCREWDRIVER - MEDIUM
D250B, D25C, D25D, D300B, D30C, D350C, D35C, D35HP, D400, D40D
2U5062 SCREWDRIVER - LARGE
D250B, D25C, D25D, D300B, D30C, D350C, D35C, D35HP, D400, D40D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.