AVSPARE.COM
parts catalog

SEAL-PISTON 2333331 - Caterpillar



2333331 SEAL-PISTON Caterpillar parts SEAL
Rating:
36
Alternative (cross code) number:
CA2333331
233-3331
2333331
Caterpillar 2333331 SEAL-PISTON
Weight: 0.01 pounds 0 kg.

Buy SEAL-PISTON 2333331 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 10 g00704407
Use Tooling (D) to remove bearing (14) from the frame assembly.
Illustration 11 g00704415
Use Tooling (D) to remove bearing (15) from the frame assembly.Installation Procedure
Note: Cleanliness is an important factor. Before the installation procedure, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble.
Verify that all of the components are clean and free of foreign material prior to installation.
Inspect all components for wear and replace the components, if necessary.
Illustration 12 g00704415
Illustration 13 g00704407
Prior to installation, lower the temperature of bearings (14) and (15) to a temperature of −45°C (−49.0°F).
Use Tooling (D) to install bearing (15) into the frame assembly.
Use Tooling (D) to install bearing (14) into the frame assembly.
Illustration 14 g00704402
Use Tooling (A) to position center arm (7) for installation into the frame assembly.
Illustration 15 g00704399
Illustration 16 g00522079Note: Align slot (X) on pin (13) with lock (11) prior to installation. It will be difficult to align after pin (13) is installed into center arm (5).
Align the bore of center arm (7) with the bore of the frame assembly. Insert pin (13) through the lower bore of the frame assembly. Insert pin (13) through the bore of center arm (7).
Measure the distance from the top of center arm (7) to the bottom of the frame assembly. Assemble shim pack (10) to obtain a gap of −.7 .6 mm (0.03 0.02 inch).
Position shim pack (10) so that pin (13) can be inserted into the top bore of the frame assembly.
Position pin (13) so that lock (9) can be installed.
Install two bolts (12) into center arm (7) and through lock (11). Tighten two bolts (12) to a torque of 370 50 N m (272.90 36.88 lb ft).
Remove Tooling (A) from center arm (7).
Illustration 17 g00704356
Connect two hose assemblies (8) and (9).
Illustration 18 g00522023
Attach Tooling (A) to steering link (1).
Illustration 19 g00522080
Apply Tooling (G) to the threads and the taper of ball stud (4).
Use Tooling (A) to lift steering link (1) so that ball stud (4) can be inserted into center arm (5).
Illustration 20 g00522017
Illustration 21 g00704435
Use Tooling (E) to install locknut (3) onto ball stud (4). Tighten locknut (3) to a torque of 2060 100 N m (1519.4 73.8 lb ft).
Illustration 22 g00704196
Install plug (6). Use Tooling (H) to install retaining ring (5). Install retaining ring (5) onto steering link (1).
Connect hose assembly (2) to steering link (1).
Repeat Steps 15 through 19 for the remaining steering link.
Check the alignment of the front wheels. Refer to Steering Systems Operation/Testing and Adjusting, SENR1492, "Front Wheel - Align" for the correct procedure.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.