AVSPARE.COM
parts catalog

SEAL-PACKING 2333569 - Caterpillar



2333569 SEAL-PACKING Caterpillar parts SEAL
Rating:
11
Alternative (cross code) number:
CA2333569
233-3569
2333569
Caterpillar 2333569 SEAL-PACKING

Buy SEAL-PACKING 2333569 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 3 g00512798
Install O-ring seal (50) and the transmission and transfer gears.
Illustration 4 g00512793
Illustration 5 g00512796
Install the washers and 24 bolts (49) .Note: During the installation of bolts (49) , tighten the bolts to a torque of 520 70 N m (384 52 lb ft).
Illustration 6 g00512791
Connect harness connector (46) for transmission oil temperature sensor (47) .
Install O-ring seal (45) . Connect hose assembly (42) . Install split flange (44) , four washers, and four bolts (43) .
Illustration 7 g00512788
Install O-ring seal (37) . Connect hose assembly (34) . Install split flange (36) , four washers, and four bolts (35) .
Install two O-ring seals (40) , magnetic screen assembly (38) , three washers, bolt (41) , and two bolts (39) .
Illustration 8 g00512787
Install four bolts (26) , block assembly (27) , and O-ring seal (28) . Install O-ring seal (30) . Connect hose assembly (29) .
Repeat Step 8 for remaining hose assembly (32) .
Install O-ring seal (22) and elbow (21) . Install O-ring seal (24) . Connect hose assembly (23) .
Repeat Step 10 for remaining hose assembly (25) .
Position the harness. Connect harness connector (33) .
Install clip (20) and bolt (31) .Note: During the installation of bolt (31) , tighten the bolt to a torque of 48 4 N m (35.4 2.9 lb ft).
Install guard (18) , clip (20) , two washers, and remaining two bolts (17) .
Illustration 9 g00512786
Connect three transmission solenoids (19) .
Install clip (20) , two washers, and two bolts (17) on guard (18) .
Illustration 10 g00512785
Use Tool (C) in order to connect harness (13) on the transmission output speed sensor of the EPTC II.
Install lockwire (16) .
Install clip (14) , the washer, and bolt (15) .Note: During the installation of bolt (15) , tighten the bolt to a torque of 410 50 N m (302.4 36.9 lb ft).
Illustration 11 g00512783
Install two spacers (12) , guard (9) , two washers, two bolts (10) , and two grommets (11) .Note: During the installation of bolts (10) , tighten the bolts to a torque of 47 9 N m (34.7 6.6 lb ft).
Illustration 12 g00512781
Illustration 13 g00512782
Use a suitable hoist to support main drive shaft (7) . Use a suitable bar to extend drive shaft (7) .
Install spider (6) and four bolts (8) .Note: During the installation of bolts (5) and (8) , use new bolts. Use Tool (B) to tighten bolts (5) and (8) to a torque of 550 20 N m (405.7 14.8 lb ft).
Install four bolts (5) .
Illustration 14 g00512774
Remove plug (1) and plug (3) . Install O-ring seal (2) and O-ring seal (4) . Install plug (1) and plug (3) .
Fill the transmission and transfer gears to the correct level with oil. Refer to Operation and Maintenance Manual.End By:
Install the drive shaft guard (rear). Refer to Disassembly and Assembly, "Drive Shaft Guard (Rear) - Install".
Remove the truck body retaining cable. Refer to Disassembly and Assembly, "Truck Body Retaining Cable - Remove and Install".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.