AVSPARE.COM
parts catalog

SEAL-PACKING 2333608 - Caterpillar



2333608 SEAL-PACKING Caterpillar parts SEAL
Rating:
81
Alternative (cross code) number:
CA2333608
233-3608
2333608
Caterpillar 2333608 SEAL-PACKING

Buy SEAL-PACKING 2333608 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 7 g00953837
Remove bolts (10) to remove steering arm (9) from the front spindle (11).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 4C-3386 Spanner Wrench 1
B 5S-6084 Socket (3 1/2 inch) 1
478-3993 Hydraulic Torque Wrench 1
385-3995 Hydraulic Pump Gp 1
384-8916(1) Hydraulic Pump Gp 1
D 1U-7505 Transmission Jack 1
485-8004 Support Stand 1
E - Retaining Ring Pliers 1
F - Loctite Graphite-50 -
(1) Available SubstituteNote: Cleanliness is an important factor. Before the installation procedure, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble.
Check all the O-ring seals and the components for wear or damage. Replace the components, if necessary.
Lubricate all the O-ring seals lightly with the lubricant that is being sealed.
Illustration 8 g00953837
Illustration 9 g01563097
Use a suitable lifting sling and a hoist to support steering arm (9). The weight of steering arm (9) is approximately 103 kg (227 lb).
Position steering arm (9) on front spindle (11). Install bolts (10) to secure steering arm. Tighten bolts (10) to a torque of 1800 200 N m (1300 150 lb ft).
Illustration 10 g00953996
Use Tooling (D) to support the weight of steering cylinder (4). The steering cylinder weighs approximately 111 kg (245 lb).
Apply Tooling (F) to the threads of the ball stud and on the taper of the ball stud.
Install steering cylinder (4) in steering arm (9).
Apply Tooling (F) to the face of locknut (8). Install the locknut loosely on the ball stud for the steering cylinder.
Illustration 11 g00953506
Position Tooling (D) to support the weight of the steering link (3). The weight of the steering link is approximately 115 kg (253 lb).
Repeat Step 6 for the ball stud on the steering link.
Install steering link (3) in steering arm (9).
Repeat Step 4 for the ball stud on the steering link.
Illustration 12 g00953489
Install Tooling (A) to hold the ball stud (7) while the locknut (8) is being tightened.
Illustration 13 g00953495
Use Tooling (B) to tighten locknut (8) on the steering cylinder. Tighten locknut (8) to a torque of 2060 100 N m (1519 74 lb ft).
Repeat Steps 13 and 14 to tighten the ball stud on the steering link.
Illustration 14 g00953479
Install plug (5). Use Tooling (E) to install retaining ring (6) onto the ball stud for the steering cylinder . Install retaining ring (6).
Repeat Step 3 for the ball stud on the steering link.
Illustration 15 g00522549
Connect hose assembly (2) to the rod end of steering cylinder (4).
Connect hose assembly (1) to steering link (3).
Check the alignment of the front wheels. Refer to Steering Systems Operation/Testing and Adjusting, SENR1492, "Front Wheel - Align" for the correct procedure.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.