AVSPARE.COM
parts catalog

SEAL-PACKING 2333625 - Caterpillar



2333625 SEAL-PACKING Caterpillar parts SEAL
Rating:
51
Alternative (cross code) number:
CA2333625
233-3625
2333625
Caterpillar 2333625 SEAL-PACKING

Buy SEAL-PACKING 2333625 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Use Tooling (D) to install Duo-Cone seal (10) in wheel assembly (4). Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Lightly lubricate the contacting surface of Duo-Cone seal (10).
Use the following procedure to install Tooling (B) in the hole of hub (8):
Illustration 10 g00523302
Position the suitable lifting device in the hole of hub (8).
Illustration 11 g00523329
Install the bolt between the suitable lifting device and the hole.
Illustration 12 g00523332
Fasten the suitable lifting device to the bolt by tying the suitable lifting device around the bolt, as shown. This will prevent the bolt from moving during the installation of hub (8).
Illustration 13 g00523334
Repeat Steps 9.a through 9.c in order to install Tooling (B) in the two remaining holes.
Attach a suitable lifting device to the lifting slings. The weight of hub (8) and ring gear (9) as a unit is approximately 68 kg (150 lb). Install hub (8) and ring gear (9) in wheel assembly (4).
Illustration 14 g00523558
Illustration 15 g00523283
Lightly lubricate the contacting surface of Duo-Cone seal (7). Use Tooling (D) to install Duo-Cone seal (7) in spindle assembly (5). Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Install bearing cone (6) on spindle (5). Bearing cone (6) is a slip fit to the spindle.
Illustration 16 g00523108
Install Tooling (A) and a suitable lifting device to wheel assembly (4). Install wheel assembly (4) to spindle assembly (5). The weight of wheel assembly (4) is approximately 127 kg (280 lb). Note: Steps 15 through 27 are for the proper wheel bearing adjustment.
Illustration 17 g00523106
Illustration 18 g00523105
Use an outside micrometer to measure the thickness of retainer plate (2) at each of the three small gauge holes. Average the three measurements and record the result.
Install retainer plate (2) without the shims. Apply oil on threads of three bolts (1) and install the bolts on retainer plate (2). The three bolts must be separated by 120 degrees.
Tighten three bolts (1) to a torque of 115 15 N m (85 10 lb ft).
Rotate the wheel by 360 degrees. Check bolts (1) and tighten the bolts (1) again, if necessary.
Loosen bolts (1). Rotate the wheel by 360 degrees in order to unload the bearings.
Tighten bolts (1) to a torque of 20 7 N m (15 5 lb ft).
Rotate the wheel by 360 degrees. Check bolts (1) and tighten bolts (1) again, if necessary.
Illustration 19 g00523642
Use Tooling (C) to measure the depth through the three small gauge holes of retainer plate (2). Average the three measurements and record the result.
Subtract the average thickness of the retainer plate from the average depth. Refer to Steps 15 and 22. The difference is the gap between the end of the spindle and retainer plate (2). This gap is the required thickness of shims.
Use Tooling (C) to measure the shim pack. The thickness of the shim pack must be within 0.025 mm (0.001 inch) of the required thickness.
Remove bolts (1) and retainer plate (2).
Illustration 20 g00523107
Install the required number of shims (3).
Illustration 21 g00523105
Install retainer plate (2) and remaining bolts (1). Tighten remaining bolts (1) to a torque of


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.