parts catalog

SEAL-PACKING 2333641 - Caterpillar

2333641 SEAL-PACKING Caterpillar parts SEAL
Alternative (cross code) number:
Caterpillar 2333641 SEAL-PACKING

Buy SEAL-PACKING 2333641 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     2P-8250     Strap Wrench Assembly     1    Start By:
Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Remove".
Remove the valve cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g01062266
Disconnect harness assembly (1). Lay harness assembly (1) out of the way.
Illustration 2 g01062271
Remove nuts (2), the bolts, and the washers.
Remove hose (3) .
Use Tooling (A) to remove fuel filter (5). Disconnect hose assembly (4). Plug all openings immediately.
Remove bolt (6), the washer, and the clip.
Disconnect harness assembly (7) and cut cable straps (8) .
Illustration 3 g01062274
Remove nut (9), the washer, and the clip.
Loosen bolt (10) until harness assembly (11) can be disconnected. Disconnect harness assembly (11). Position the harness assembly away from the cylinder head.
Illustration 4 g01062275
Disconnect fittings (12). Remove bolts (13) and the washers. Remove tube assembly (14) .
Illustration 5 g01062276
Remove bolts (15) and the washers. Remove water outlet manifold (16) .
Remove the spacers from the head bolt studs.
Illustration 6 g01062278
Note: Engines that are equipped with a compression brake will have three head bolt studs. The three head bolt studs are installed in place of head bolts. Remove the head bolt studs with the head bolts.
Remove head bolts (17) and the head bolt studs, if equipped.
Remove the gasket from cylinder head (18) .
Illustration 7 g01062281
Attach a suitable lifting device to cylinder head (18). Ensure that all wires, lines, and hoses are free from the cylinder head.
Carefully remove cylinder head (18) from the cylinder block. The weight of cylinder head (18) is approximately 135 kg (300 lb).
Remove cylinder head gasket (19) and the O-ring seals from the cylinder block.

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.