AVSPARE.COM
parts catalog

SEAL-PACKING 2333654 - Caterpillar



2333654 SEAL-PACKING Caterpillar parts SEAL
Rating:
46
Alternative (cross code) number:
CA2333654
233-3654
2333654
Caterpillar 2333654 SEAL-PACKING
Weight: 0.01 pounds 0 kg.

Buy SEAL-PACKING 2333654 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 5 g00524942
Pull plug (18) against accumulator (1) in order to seat plug (18), as shown.
Illustration 6 g00570098
Install washer (22), O-ring seal (21) and backup ring (20) onto accumulator (1).
Illustration 7 g00524940
Illustration 8 g00524941
Install spacer (19) onto plug (18). Use Tool (A) (not shown) in order to install locknut (17). Tighten locknut (17) to a torque of 102.5 7.5 N m (75.6 5.52 lb ft).
Illustration 9 g00524930
Install valve (8) into adapter (7). Install O-ring (6) onto adapter (7).
The following procedure illustrates the preparation of the bladder prior to installation.
Install valve assembly (4) onto the end of the bladder. Inflate the new bladder or the used bladder to normal size in order to check for leakage. Bladders should be inflated to a maximum of 21 kPa (3 psi).
Use a solution of soap and water in order to check the bladder for leaks. If a leak is detected, the bladder must be replaced with a new bladder. After testing, deflate the bladder immediately.
Remove valve assembly (4) from the end of the bladder. Purge the air from the bladder and fold the bladder lengthwise into a compact roll. Once the bladder is folded, install valve assembly (4).
Pour clean hydraulic oil into accumulator (1). Fill 10% of the volume of accumulator (1) with hydraulic oil. Note: The bladder is lubricated and cushioned by the hydraulic oil.
Illustration 10 g00527929
Insert bladder (3) into accumulator (1).
Illustration 11 g00524938
Insert plug (12) into accumulator (1).
Illustration 12 g00524937
Fold ring (16) in order to insert ring (16) into accumulator (1). Unfold ring (16). Position ring (16) at the end of accumulator (1).
Illustration 13 g00524936
Illustration 14 g00524935
Pull plug (12) against accumulator (1) in order to seat plug (12), as shown.
Install washer (15), O-ring seal (14) and backup ring (13) onto accumulator (1).
Illustration 15 g00524934
Illustration 16 g00524932
Install spacer (11) onto plug (12). Use Tool (A) in order to install locknut (10). Tighten locknut (10) to a torque of 102.5 7.5 N m (75.6 5.52 lb ft).
Illustration 17 g00524931
Install nut (9) onto the end of bladder (3). Tighten nut (9) to a torque of 30.5 3.5 N m (22.5 2.58 lb ft).
Illustration 18 g00524866
Install cover (2) onto accumulator (1). End By:
Install the steering accumulator. Refer to Disassembly and Assembly, "Steering Accumulator - Install".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.