AVSPARE.COM
parts catalog

SEAL-PISTON 2333861 - Caterpillar



2333861 SEAL-PISTON Caterpillar parts SEAL
Rating:
56
Alternative (cross code) number:
CA2333861
233-3861
2333861
Caterpillar 2333861 SEAL-PISTON

Buy SEAL-PISTON 2333861 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 127-4904 Hydraulic Cylinder Repair Stand 1
A 3S-6224 Electric Hydraulic Pump 1
B 8T-5245 Torque Multiplier 1
B 1P-0851 Spline Adapter 1
B 2P-2265 Mounting Assembly 1
B 5S-6079 Socket 1
C 5P-2980 Seal Installer 1
D 1P-0510 Driver Group 1
E 2P-8301 Seal Guide 1 Note: Cleanliness is an important factor. Before the assembly procedure, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble.
Check all of the O-ring seals and the components for wear of damage. Replace the components, if necessary.
Illustration 1 g00537680
Illustration 2 g00537682
Illustration 3 g00535129
Lubricate all of the O-ring seals lightly with the lubricant that is being sealed.
Use Tool (C) (not shown) in order to install seal assembly (11) into head (3), as shown.
Use Tool (C) (not shown) in order to install U-cup seal (10) into head (3), as shown. Note: Prior to installation of lip seal (9), apply 4C-4032 Bearing Mount Compound to the lip seal groove.
Use Tooling (D) in order to install lip seal (9) into head (3), as shown.
Illustration 4 g00535131
Use two 7/8 inch - 9 NC bolts in order to position head (3) onto cylinder assembly (4).
Align piston rod (1) with head (3). Install Tool (E) (not shown) onto piston rod (1).
Use Tooling (A) in order to push piston rod (1) through head (3) and into cylinder assembly (4).
Remove two 7/8 inch - 9 NC bolts in order to separate head (3) from cylinder assembly (4). Use Tooling (A) in order to separate piston rod (1) and head (3) as a unit from cylinder assembly (4).
Remove Tool (E) (not shown) from piston rod (1).
Illustration 5 g00535063
Install seal assembly (8) onto piston (5), as shown.
Install wear ring (7) onto piston (5), as shown.
Illustration 6 g00535062
Position piston (5) onto piston rod (1), as shown.
Lubricate the threads of locknut (6). Install locknut (6) onto piston rod (6). Use Tooling (B) in order to tighten locknut (6) to a torque of 2200 220 N m (1622.6 162.3 lb ft).
Remove Tooling (B).
Illustration 7 g00535060
Use Tooling (A) in order to position piston rod (1) and head (3) into cylinder assembly (4) as a unit.
Install four bolts (2) and the washers. Do not tighten four bolts (2) at this time.
Failure to follow the recommended procedure or the specified tooling that is required for the procedure could result in damage to components.To avoid component damage, follow the recommended procedure using the recommended tools.
Use Tooling (A) in order to fully extend piston rod (1).
Tighten four bolts (2) to a torque of 620 80 N m (457 59 lb ft).
Illustration 8 g00535058
Remove the steering cylinder from Tooling (A). End By:
Install the steering cylinder. Refer to Disassembly and Assembly, "Steering Cylinder - Assemble".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.