AVSPARE.COM
parts catalog

SEAL-PISTON 2333909 - Caterpillar



2333909 SEAL-PISTON Caterpillar parts SEAL
Rating:
86
Alternative (cross code) number:
CA2333909
233-3909
2333909
Caterpillar 2333909 SEAL-PISTON

Buy SEAL-PISTON 2333909 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the cooling system pressure cap is cool enough to touch with your bare hand.Remove the cooling system pressure cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Drain the coolant from the radiator into a suitable container so that the level of the radiator is below the level of the expansion tanks. The capacity of the cooling system is approximately 568 L (150 US gal).
Illustration 1 g01013115
Remove bolts (5), washers (6), and left cover (4) .
Remove bolts (2), washers (3), and right cover (1) .
Illustration 2 g00538847
Open the hood in order to access the lower tube (7) of the expansion tank.
Remove the four bolts and the four washers in order to disconnect tube (8) (not shown).
Illustration 3 g00538574
Disconnect hose assembly (9) .
Remove the washer and bolt (12) .
Disconnect harness assembly (11) .
Remove the additional bolt. Disconnect liquid level sensor (10) of the jacket water.
Remove bolts (13) and washers (14) .
Illustration 4 g00538848
Disconnect hose assembly (15) and hose assembly (16) .
Remove a washer and bolt (17) .
Disconnect harness assembly (18) .
Remove the additional bolt. Disconnect liquid sensor (19) of the aftercooler.
Remove bolts (20) and washers (21) .
Illustration 5 g01006090
Use Tooling (A) and a suitable lifting device to remove expansion tank (22) from the hood. The weight of the expansion tank is approximately 172 kg (379 lb).Installation Procedure
Illustration 6 g01006090
Use Tooling (A) and a suitable lifting device to install expansion tank (22) on the hood. The weight of expansion tank (22) is approximately 172 kg (379 lb).
Illustration 7 g00538848
Install washers (21) and bolts (20) .
Connect liquid sensor (19) of the aftercooler. If necessary, install the bolt and the washer.
Connect harness assembly (18) .
Install a washer and bolt (17) .
Connect hose assembly (16) and hose assembly (15) .
Illustration 8 g00538574
Install washers (14) and bolts (13) .
Connect liquid level sensor (10) of the jacket water. Install the bolt and the washer.
Connect harness assembly (11) .
Install a washer and bolt (12) .
Connect hose assembly (9) .
Illustration 9 g00538847
Connect tube (8) (not shown). Install four washers and four bolts.
Connect tube (7). Install four washers and four bolts.
Illustration 10 g01013115
Install right cover (1), washers (3), and bolts (2) .
Install left cover (4), washers (6), and bolts (5) .
Fill the radiators to the correct level with coolant. Refer to Operation and Maintenance Manual, "Extended Life Coolant (ELC)" for the correct level.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.