AVSPARE.COM
parts catalog

SEAL-ROD 2333920 - Caterpillar



2333920 SEAL-ROD Caterpillar parts SEAL
Rating:
41
Alternative (cross code) number:
CA2333920
233-3920
2333920
Caterpillar 2333920 SEAL-ROD

Buy SEAL-ROD 2333920 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 29 g00539550
Connect hose (40) to the hood of the expansion tank. Close the front hood and the rear hood.
Illustration 30 g00539549
Connect harness assemblies (37) and (38). Install two cable straps (39) that hold harness assemblies (37) and (38) to the expansion tank. Push harness assemblies (37) and (38) through the hood of the expansion tank. Install grommet (36) .
Connect hose (40) to the hood of the expansion tank.
Illustration 31 g00539548
Connect harness assemblies (33) and (34). Install two cable straps (32) that hold harness assemblies (33) and (34) to the expansion tank. Push harness assemblies (33) and (34) through the hood of the expansion tank. Install grommet (35) .
Connect hose (31) to the expansion tank.
Illustration 32 g00539547
If the truck has a service center, position plate (30) on the front bumper. Install ten bolts (29). If the truck does not have a service center, position plate (30) on the front bumper. Install eleven bolts (29) .
Illustration 33 g00539546
Position gasket (24) and drain elbow (26) on the radiator. Install bolts (25) that hold drain elbow (26) to the radiator.Note: Use a new part during the installation of gasket (24) .
Position hose (27) on the elbow. Tighten hose clamps (28) .
Illustration 34 g00539545
Position gasket (23) and drain elbow (21) on the radiator. Install bolts (22) that hold drain elbow (21) to the radiator.Note: Use a new part during the installation of gasket (23) .
Position hose (20) on the elbow. Tighten hose clamps (19) .
Illustration 35 g00539544
The frame on the lower right side of the radiator
Position harness assembly (16) and clip (17). Install bolt (18). The bolt (18) holds harness assembly (16) and clip (17) to the frame. Connect harness assembly (16) .
Illustration 36 g00539543
The frame on the lower left side of the radiator
Connect harness assembly (14). Position harness assembly (14) with cable straps. Install bolt (15) through the clip that holds harness assembly (14) to the frame assembly.
Illustration 37 g00539542
Install bolt (13). Bolt (13) holds the clip and hose (11) to the bottom of the radiator.
Illustration 38 g00539540
Install bolt (12). Bolt (12) holds the clip and hose (2) to the bottom of the radiator.
Illustration 39 g00539538
The left side of the radiator drain
Illustration 40 g00539539
The right side of the radiator drain
Be certain that drain valves (5) and (8) are in the Closed position.
Connect hoses (1), (2), (3), and (4) to the drain elbow on the left side. Connect hoses (7), (10), and (11) to the drain elbow on the right side.
Refill the engine cooling system to the correct level with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" for the correct procedures and the correct fluid capacities. The capacity of the cooling system is approximately 568 L (150 US gal).End By: Remove the truck body retaining cable. Lower the truck body. Refer to Disassembly and Assembly, "Truck Body Retaining Cable - Remove and Install".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.