AVSPARE.COM
parts catalog

SEAL-ROD 2333933 - Caterpillar



2333933 SEAL-ROD Caterpillar parts SEAL
Rating:
26
Alternative (cross code) number:
CA2333933
233-3933
2333933
Caterpillar 2333933 SEAL-ROD

Buy SEAL-ROD 2333933 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Note: Cleanliness is an important factor. Before the installation procedure, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause later trouble.
Check all the O-ring seals and the components for wear or damage. Replace the components, if necessary.
Lubricate all the O-ring seals lightly with the lubricant that is being sealed.
Illustration 1 g00541538
Use a suitable lifting device and a hoist to position rod (6) horizontally on wood blocks. The weight of rod (6) is 159 kg (350 lb).
Use Tooling (A) to install one retaining ring (14) to rod (6).
Lower the temperature of bearing (15) to −50 °C (−58 °F). Position bearing (15) into rod (6) until bearing (15) is seated against retaining ring (14).
Use Tool (A) to install the remaining retaining ring (14) into rod (6).
Illustration 2 g00541540
Install plate (12), and ball (13) to rod (6).
Illustration 3 g00541545
Install wear ring (11) to rod (6).
Repeat Steps 3 through 6 for the head of cylinder (16) (not shown). The weight of cylinder (16) is 172 kg (380 lb).
Illustration 4 g00541580
Use a suitable lifting device and a hoist to place cylinder (16) in a vertical position. Support the head end of cylinder (16) in a suitable fixture. The weight of cylinder (16) is 172 kg (380 lb).
Illustration 5 g00541552Note: Prior to the installation of rod (6), apply clean oil to the bore of cylinder (16).
Use a suitable lifting device and a hoist to install rod (6) into cylinder (16). The weight of rod (6) is 159 kg (350 lb).
Illustration 6 g00541546
Install lip seal (9) and U-cup seal (10) to head (5).
Illustration 7 g00541548
Install backup ring (7) and O-ring seal (8) to head (5).
Illustration 8 g00541550
Use a suitable lifting device and a hoist to install head (5) to rod (6). Align the bolt pattern in head (5) to the bolt pattern in the cylinder. The weight of head (5) is 39 kg (86 lb).
Illustration 9 g00541556
Install 15 bolts (4) and the washers to head (5). Use Tooling (B) to tighten 15 bolts (4) to a torque of 215 40 N m (159 30 lb ft).
Illustration 10 g00541579
Install cover (3) with two bolts (2) and two washers. Use Tooling (B) (not shown) to tighten two bolts (2) to a torque of 215 40 N m (159 30 lb ft).
Repeat Step 16 for the remaining cover that is on the opposite side of the rear suspension cylinder.
Illustration 11 g00541551
If it is necessary, install three grease fittings (1) to the rear suspension cylinder.
Apply 5P-0960 Molybdenum Grease to the grease fittings.End By:
Install the rear suspension cylinders. Refer to Disassembly and Assembly, "Rear Suspension (Cylinder) - Install".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.