62000221 SERVO SLEEVE KIT Caterpillar parts
CB-514
Rating:
Alternative (cross code) number:
CA62000221
6200-0221
62000221
CA62000221
6200-0221
62000221
VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
£291.08
12 Apr 2018
AutoRedimension: AutoRedimension
Front Bumper with First 62000221
Number on catalog scheme:
18
For full view, you need register
Compatible equipment models: 62000221:
Information:
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Lower the blade to the ground. Release the air pressure in the air tanks. Refer to Operation and Maintenance Manual, "Air Tank Moisture and Sediment - Drain" for the correct procedure.
Illustration 1 g00928777
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Disconnect hose assemblies (3) .
Remove bolts (2) that hold housing (1). Remove housing (1) .Note: Bolts (2) must be removed evenly.
Illustration 2 g01073003
Remove O-ring seal (7), washers (6), and springs (5) .
Illustration 3 g00929681
Use a hammer to loosen pin (9) from lock bar (8) .
Illustration 4 g00929682
Remove pin (9) from housing (10). Remove housing (10) .
Illustration 5 g00928838
Remove bolts (16), lock (15), plate (14), seals (13), piston (12), and O-ring seal (11) from pin (9) .
Illustration 6 g01076596
Remove seals (17) and back up rings (18) from housing (10) .
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Lower the blade to the ground. Release the air pressure in the air tanks. Refer to Operation and Maintenance Manual, "Air Tank Moisture and Sediment - Drain" for the correct procedure.
Illustration 1 g00928777
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Disconnect hose assemblies (3) .
Remove bolts (2) that hold housing (1). Remove housing (1) .Note: Bolts (2) must be removed evenly.
Illustration 2 g01073003
Remove O-ring seal (7), washers (6), and springs (5) .
Illustration 3 g00929681
Use a hammer to loosen pin (9) from lock bar (8) .
Illustration 4 g00929682
Remove pin (9) from housing (10). Remove housing (10) .
Illustration 5 g00928838
Remove bolts (16), lock (15), plate (14), seals (13), piston (12), and O-ring seal (11) from pin (9) .
Illustration 6 g01076596
Remove seals (17) and back up rings (18) from housing (10) .
Caterpillar parts catalog:
Parts servo Caterpillar catalog:
62000239
SERVO PISTON KIT
CB-514
CB-514