1695470 SHAFT GP-VIBRATORY Caterpillar parts 10 FT, 10B, 8 FT SHAFT
Rating:
Alternative (cross code) number:
CA1695470
169-5470
1695470
CA1695470
169-5470
1695470
ASPHALT SCREED,
For full view, you need register
Information:
Illustration 1 g00826591
Schematic for the Power Train ECMThis diagnostic code is recorded when the power train ECM does not recognize the harness code that is received from the Caterpillar Monitoring System on the data link (wires 944-OR and 945-BR).Note: Ensure that the diagnostic code is active and that the diagnostic code indicator is active.Test Step 1. CHECK THE HARNESS CODE
Turn the key start switch to the OFF position.
Disconnect the machine harness from the control module.
Measure the continuity from contact 2 to contact 3. Measure the continuity from contact 2 to contact 9.Expected Result:There is NOT continuity.Results:
YES - There is NOT continuity. The circuitry for the harness has failed.Repair: Repair the harness or replace the harness. Clear the fault. Stop.
NO - There is continuity. The circuitry for the harness is functioning correctly.Repair: The transmission electronic control module may have failed. This is unlikely. Proceed to Test Step 2.Test Step 2. VERIFY THAT THE TRANSMISSION ELECTRONIC CONTROL MODULE HAS FAILED
Connect the machine harness to the control module.
Turn the key start switch to the ON position.
Verify that the diagnostic code is present. Verify that the diagnostic code is active.
Turn the key start switch to the OFF position.
Turn the key start switch to the ON position.
Verify that the diagnostic code is present. Verify that the diagnostic code is active.Expected Result:The diagnostic code is active.Results:
YES - The diagnostic code is active. The transmission electronic control module has failed.Repair: It is unlikely that the power train ECM has failed. Exit this test procedure and perform this test procedure again. If the cause of the problem is not found, replace the power train ECM. Refer to Testing and Adjusting, "Electronic Control Module (Power Train) - Replace". Stop.
NO - The diagnostic code is not active.Repair: Clear the diagnostic code. Watch for a recurrence of this diagnostic code. Stop.
Caterpillar SIS machinery equipment:
Caterpillar SIS
- 8B Pavemaster Screed 3LM00001-UP » 169-5470 SHAFT GP-VIBRATORY
- 10B Pavemaster Screed 3PM00001-UP » 169-5470 SHAFT GP-VIBRATORY
- 10B PAVEMASTER Screed BKB00001-UP » 169-5470 SHAFT GP-VIBRATORY
Parts shaft Caterpillar catalog:
1121276
SHAFT GP-DRIVE
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP1000E, AP1055E, AP555E, AS2251, AS2301, AS3251C, AS3301C, BG-225B, BG-225C, BG-24...
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP1000E, AP1055E, AP555E, AS2251, AS2301, AS3251C, AS3301C, BG-225B, BG-225C, BG-24...
1233686
SHAFT-IDLER
10 FT, 10-20B, 8 FT, 8-16B, AP-800C, BG-225B
10 FT, 10-20B, 8 FT, 8-16B, AP-800C, BG-225B
1713711
SHAFT-GEAR
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-1055D, AP-600D, AP-655D, AP-800C, AS2251, AS2252C, AS2301, AS2302, AS2302C, AS3251C, AS3301C, AS4252C, BG-225B, BG-2455C, BG-2455D, BG-260D, CS-663E, CS-683E
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-1055D, AP-600D, AP-655D, AP-800C, AS2251, AS2252C, AS2301, AS2302, AS2302C, AS3251C, AS3301C, AS4252C, BG-225B, BG-2455C, BG-2455D, BG-260D, CS-663E, CS-683E
8I0145
SHAFT AS-VIBRATORY
10 FT, 10-20B, 10B, AP-1055D, BG-2455C, BG-2455D, BG-260D
10 FT, 10-20B, 10B, AP-1055D, BG-2455C, BG-2455D, BG-260D
10 FT, 10B, 8 FT, 8-16B, AP-800C, BG-225B
1204787
SHAFT AS-VIBRATORY
10 FT, 10B, 8 FT
10 FT, 10B, 8 FT
1237437
SHAFT AS-DRIVE
10 FT, 10B, 8 FT
10 FT, 10B, 8 FT
1237438
SHAFT AS-DRIVE
10 FT, 10B, 8 FT
10 FT, 10B, 8 FT
1106222
SHAFT AS
10 FT, 10B, 8 FT
10 FT, 10B, 8 FT