AVSPARE.COM
parts catalog

SHAFT GP-DRIVE 3967838 - Caterpillar



3967838 SHAFT GP-DRIVE Caterpillar parts 901C SHAFT
Rating:
60
Alternative (cross code) number:
CA3967838
396-7838
3967838
Caterpillar 3967838 SHAFT GP-DRIVE

Buy SHAFT GP-DRIVE 3967838 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT WHEEL LOADER,

Compatible equipment models: 3967838:

COMPACT WHEEL LOADER  901C   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 7 g03891261
Using the arrow button, select the set of heads you would like to calibrate and push "OK".
Illustration 8 g03891269
Using the arrow button, select "Enable" then push "OK" to enable the calibration process.
Illustration 9 g03891278
You are taken back to the same screen shown in step 4. Use the back arrow button to exit to the calibration screen.
Illustration 10 g03891287
Once 2-5 Head Calibration Screen is visible, put machine in manual mode.
The head selected should be the head that is turned on using manual mode. Only one head should be on at a time during calibration.
Once the water is activated, push the accelerator to the floor to achieve the 2000 RPM target. Once the target is met, the light will turn green.Note: The water pressure should automatically settle out to 80 PSI. The light will turn green, if the system is working correctly.
Begin the head adjustment. Press the corresponding F(X) button below the head being calibrated.
Illustration 11 g03891298
Use the arrow buttons to increase or decrease hydraulic pressure, then select "OK" when the correct pressure is reached.
After adjusting the value press OK button. If the hydraulic pressure is within 345 kPa (50 PSI) plus or minus of the target pressure, the light will turn green.Note: Adjust the head intensity until the green light remains on for a long time.
Spray head is calibrated once all the lights are green. Once accomplished, then proceed to next spray head.Keypad
Illustration 12 g03145458
Keypad (D)
Note: The indicator lights next to each button will illuminate green when the button is activated. (11) Configuration Modes - The configuration modes are for automatic (preset) operation of a single or multiple heads. When no other buttons functions are active, the numbered buttons will select a configuration mode. The modes selected will appear on the WDS display. The water pump on/off must be turned "ON" with the configuration for the water pump to turn "ON" automatically at a preset minimum machine speed. This preset minimum m/c speed can be adjusted using the configuration setup options. (12) Manual - The Manual button puts the water system in a manual mode. When the manual mode is activated, the numbered buttons will turn on/off the spray head with that number as seen on the display. Manual mode can be used when the m/c is moving forward or reverse. (13) Head Clean - The Head Clean button activates the head clean mode. Press a numbered button after head clean mode is activated to open the selected head to the maximum opening and flush the head of any debris. The head will gravity feed unless the pump is turned on. When the pump is turned on, the heads will pressure clean at (default) 207 kPa (30 psi). (14) Cannon - The Cannon button enables the water cannon. The cannon position can be controlled with the joystick. The cannon can also be enabled at the same time as manual mode for spray heads. The pump must be turned on and the joystick trigger pulled in order to spray water from the cannon. (15)

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
901C Compact Wheel Loader W4T00001-UP (MACHINE) POWERED BY C1.8 Engine
901C2 Compact Wheel Loader YKY00001-UP (MACHINE) POWERED BY C1.7 Engine


Parts shaft Caterpillar catalog:

3830400 SHAFT-GEAR
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3391738 SHAFT
901C, 902C, 903C
4423590 SHAFT
901C, 902C, 903C
4423591 SHAFT
901C, 902C, 903C
4423601 SHAFT
901C, 902C, 903C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.