AVSPARE.COM
parts catalog

SHAFT GP-DRIVE 4646908 - Caterpillar



4646908 SHAFT GP-DRIVE Caterpillar parts SHAFT
Rating:
21
Alternative (cross code) number:
CA4646908
464-6908
4646908
Caterpillar 4646908 SHAFT GP-DRIVE

Buy SHAFT GP-DRIVE 4646908 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

Autolube Piston Detector Switch
Illustration 1 g00587675
Autolube Piston Detector Switch (1) Schematic Symbol (2) SwitchThe VIDS uses three autolube piston detector switches. The three autolube distribution manifolds have a dedicated Autolube Piston Detector Switch. The switches OPEN and the switches CLOSE as the lubricant is pumped through the system. If any of the lubricant lines are plugged the switches will not cycle. A message is shown on the message center at the end of a lubrication cycle when a switch or switches have failed to complete at least one "ON\OFF\ON" or "OFF\ON\OFF" cycle. The status display for the switch is unimportant since the switch can be either OPEN or CLOSED.Hydraulic Oil Level Switch
Illustration 2 g00587676
Hydraulic Oil Level Switch (1) Schematic Symbol (2) Level SwitchThe hydraulic oil level switch monitors the level of the hydraulic oil after the key start switch has been in the ON position for 2 seconds and before the engine is started. The VIDS checks the hydraulic oil level with the switch. The switch opens when the hydraulic oil level is below the normal operating level. The switch is open (normally open) when the switch is removed from the machine (on the bench).Engine Oil Level Switch
Illustration 3 g00588029
Engine Oil Level Switch (1) Schematic Symbol (2) Level SwitchThe engine oil level switch monitors the level of the engine oil after the key start switch has been in the ON position for 2 seconds and before the engine is started. The VIDS checks the engine oil level with the switch. The switch opens when the engine oil level is below the normal operating level. The switch is open (normally open) when the switch is removed from the machine (on the bench).Engine Coolant Level Switch
The engine coolant level switch monitors the level of the engine coolant after the key start switch has been in the ON position for 2 seconds and before the engine is started. The VIDS checks the engine coolant level with the switch. The switch opens when the engine coolant level is below the normal operating level. The switch is open (normally open) when the switch is removed from the machine (on the bench). Air Filter Plugging Switch
Illustration 4 g00588134
Air Filter Plugging Switch (1) Schematic Symbol (2) SwitchThe air filter plugging switch is closed when the air filter is plugged. The VIDS detects the state of the switch. The status can be shown on the message center.Hydraulic Oil Filter Switch
The hydraulic oil filter switch closes the switch contacts when an acceptable pressure drop is detected across the filter. The switch closes the signal circuit to ground during normal operation. When the pressure across the filter is greater than the specified limit the switch contacts open. The VIDS warns the operator via the message center that the hydraulic oil filter switch is "PLUGGED".

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
910M Compact Wheel Loader H2200001-UP (MACHINE) POWERED BY C4.4 Engine
914M Compact Wheel Loader H2400001-UP (MACHINE) POWERED BY C4.4 Engine


Parts shaft Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.