parts catalog

SHAFT 5088214 - Caterpillar

5088214 SHAFT Caterpillar parts SHAFT
Alternative (cross code) number:
Caterpillar 5088214 SHAFT

Buy SHAFT 5088214 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have the same sealing properties as a new O-ring seal. Use Tooling (E) during the assembly procedure.
Illustration 1 g00758148
Note: Apply Tooling (F) to the outside of lip seal (9) prior to installation.Note: Lubricate the sealing lip of seal ring (7), seal (8), and lip seal (9) with the lubricant that is being used.
Install seal (6). Install seal ring (7). Install seal (8) with the lip toward the inside of the cylinder. Install lip seal (9) with the lip away from the inside of the cylinder.
Illustration 2 g00758147
Install the seal and ring (5) on the head.
Illustration 3 g00758146
Install the head in the cylinder body. Do not tighten the head. Slide the cylinder body on the rod assembly.
Unscrew the head.
Move the cylinder body away from the rod assembly after the head is on the rod assembly.
Illustration 4 g00758144
Install seals (3) and (4) on the piston.
Illustration 5 g00758143
Install piston (2). Use Tooling (D) in order to install the bolt that holds piston (2). Tighten the bolt to a torque of 1125 100 N m (830 75 lb ft).
Illustration 6 g00758141
Slide the cylinder body on the rod assembly.
Illustration 7 g00758140
Typical Example
Use Tooling (C) in order to tighten head (1) on the cylinder body. The torque for head (1) is 600 130 N m (445 100 lb ft).
Illustration 8 g00758138
Remove the tilt cylinder from Tooling (B) .
Illustration 9 g00758137
Use Tooling (A) in order to install the bearing in the rod assembly.End By: Install the tilt cylinder. Refer to Disassembly and Assembly, "Tilt Cylinder - Install".

Parts shaft Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.