63000528 SHAFT, DRIVE Caterpillar parts
CB-414
Rating:
Alternative (cross code) number:
CA63000528
6300-0528
63000528
CA63000528
6300-0528
63000528
VIBRATORY COMPACTOR,
Compatible equipment models: 63000528:
Number on catalog scheme:
2
For full view, you need register
Information:
Temperature Sender (Hydraulic Oil)
Illustration 1 g00020687
Temperature Sender (Hydraulic Oil)
The temperature sender for the hydraulic oil connects to the monitor at pin number 3. The resistance of the sender varies as the temperature changes. The table below lists the resistances:
Table 1
Resistances For Temperature Sender (Hydraulic Oil)
Temperature Resistance
0 °C (32 °F) 20824 to 25451 Ohms
25 °C (77 °F) 6134 to 7496 Ohms
35 °C (95 °F) 3989 to 4875 Ohms
50 °C (122 °F) 2224 to 2718 Ohms
75 °C (167 °F) 973 to 1189 Ohms
100 °C (212 °F) 475 to 522 Ohms
125 °C (257 °F) 221 to 269 Ohms Fuel Level Sender
Illustration 2 g00685266
Fuel Level Sender
The fuel level sender is attached to a float in the fuel tank. As the fuel level changes, the float inside the tank moves. The movement of the float will change the resistance of the sender. The voltage to the controller will change as the resistance of the sender changes. The controller will monitor this voltage and the controller will compare this voltage to values that are known. This comparison will determine the level of fuel in the tank.Hydraulic Level Switch and Engine Oil Level Switch
Illustration 3 g00662559
Hydraulic Oil Level Switch
The hydraulic oil level switch monitors the hydraulic oil level after the starter key switch is held in the ON position for 2 seconds or more. The controller checks hydraulic oil level with the switch. The switch closes when the hydraulic oil level is below the normal operating level. This switch is in the normally open position, when the switch is not installed on the machine.Engine Coolant Level Switch
The engine coolant level switch is an electronic switch that is activated by the coolant. The coolant level switch is closed to ground during normal operation. The switch opens when the coolant level is too low. The open switch informs the controller that the coolant level is too low in the cooling system. Alternator
The frequency output terminal of the alternator is connected to pin 4 of the monitoring system. The monitoring system will monitor the signal on this circuit. This signal informs the monitoring system about the relative speed that the alternator is rotating. The frequency output terminal of the alternator is the "R" terminal.
Illustration 1 g00020687
Temperature Sender (Hydraulic Oil)
The temperature sender for the hydraulic oil connects to the monitor at pin number 3. The resistance of the sender varies as the temperature changes. The table below lists the resistances:
Table 1
Resistances For Temperature Sender (Hydraulic Oil)
Temperature Resistance
0 °C (32 °F) 20824 to 25451 Ohms
25 °C (77 °F) 6134 to 7496 Ohms
35 °C (95 °F) 3989 to 4875 Ohms
50 °C (122 °F) 2224 to 2718 Ohms
75 °C (167 °F) 973 to 1189 Ohms
100 °C (212 °F) 475 to 522 Ohms
125 °C (257 °F) 221 to 269 Ohms Fuel Level Sender
Illustration 2 g00685266
Fuel Level Sender
The fuel level sender is attached to a float in the fuel tank. As the fuel level changes, the float inside the tank moves. The movement of the float will change the resistance of the sender. The voltage to the controller will change as the resistance of the sender changes. The controller will monitor this voltage and the controller will compare this voltage to values that are known. This comparison will determine the level of fuel in the tank.Hydraulic Level Switch and Engine Oil Level Switch
Illustration 3 g00662559
Hydraulic Oil Level Switch
The hydraulic oil level switch monitors the hydraulic oil level after the starter key switch is held in the ON position for 2 seconds or more. The controller checks hydraulic oil level with the switch. The switch closes when the hydraulic oil level is below the normal operating level. This switch is in the normally open position, when the switch is not installed on the machine.Engine Coolant Level Switch
The engine coolant level switch is an electronic switch that is activated by the coolant. The coolant level switch is closed to ground during normal operation. The switch opens when the coolant level is too low. The open switch informs the controller that the coolant level is too low in the cooling system. Alternator
The frequency output terminal of the alternator is connected to pin 4 of the monitoring system. The monitoring system will monitor the signal on this circuit. This signal informs the monitoring system about the relative speed that the alternator is rotating. The frequency output terminal of the alternator is the "R" terminal.