AVSPARE.COM
parts catalog

SHANK AS-RIPPER 4Z8937 - Caterpillar



4Z8937 SHANK AS-RIPPER Caterpillar parts D10R, D10T, D10T2 SHANK
Rating:
56
Alternative (cross code) number:
CA4Z8937
4Z-8937
4Z8937
Caterpillar 4Z8937 SHANK AS-RIPPER
Weight: 1416 pounds 642 kg.

Buy SHANK AS-RIPPER 4Z8937 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z8937:

TRACK-TYPE TRACTOR  D10R   D10T   D10T2   Caterpillar
Number on catalog scheme: 6
 
  For full view, you need register

Information:


Illustration 2 g01144470
Left side engine view (1) J1/P1 ECM connectors
Thoroughly inspect the J1/P1 ECM connectors and the J700/P700 engine shutdown switch connector. Also inspect each of the machine connectors that are in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01213917
Terminal locations at the P1 ECM connector (P1-5) Digital sensor return (P1-23) Engine shutdown switch (N/C) (P1-40) Engine shutdown switch (N/O)
Illustration 4 g01159881
Harness connector for the engine shutdown switch (Terminal A) Engine shutdown switch (N/O) (Terminal B) Digital return (Terminal C) Engine shutdown switch (N/C)
Perform a 45 N (10 lb) pull test on each of the wires for the engine shutdown switch.
Check the torque of the allen head screw on the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points from the switch back to the ECM.Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Shutdown Switch on Cat ET
Connect Cat ET to the service tool connector.
Restore electrical power to the ECM.
Monitor the status screen on Cat ET while you operate the shutdown switch. Observe the status for the shutdown switch.Note: Wait at least 30 seconds for the status of the switch to change.Expected Result:The status of the shutdown switch reads "ON" with the shutdown switch in the STOP position. The status of the shutdown switch reads "OFF" when the shutdown switch is in the RUN position.Results:
OK - The status of the shutdown switch reads "ON" with the shutdown switch in the STOP position. The status of the shutdown switch reads "OFF" when the shutdown switch is in the RUN position. The shutdown switch is operating normally.Repair: The circuit for the shutdown switch appears to be operating correctly. There may be an intermittent problem in the harness or in a connector. If an intermittent problem is suspected, refer to Troubleshooting, "Inspecting Electrical Connectors".STOP
Not OK - The status of the switch does not read "ON" with the shutdown switch in the STOP position. The status of the shutdown switch does not read "OFF" when the shutdown switch is in the RUN position. There is a problem with the circuit for the shutdown switch. There may be a problem with the ECM. Proceed to Test Step 3.Test Step 3. Short the Terminals at the Harness Connector for the Shutdown Switch
Remove electrical power from the ECM.
Fabricate a jumper wire that is long enough to short circuit two terminals at the harness connector for the shutdown switch. Crimp connector pins to

Caterpillar parts catalog:

Caterpillar parts catalog
D10R Custom Parts Manual Track-Type Tractor 3KR00001-UP (MACHINE)
D10R CUSTOM PARTS MANUAL TRACK-TYPE TRACTOR AKT00001-UP (MACHINE) POWERED BY 3412E Engine
D10T TRACK-TYPE TRACTOR RJG00001-UP (MACHINE) POWERED BY C27 Engine
D10T2 TRACK-TYPE TRACTOR JJW00001-UP (MACHINE) POWERED BY C27 Engine
D10T2 TRACK-TYPE TRACTOR RAB00001-UP (MACHINE) POWERED BY C27 Engine


Parts shank Caterpillar catalog:

8E5346 SHANK AS-RIPPER
D10N, D10R, D10T, D10T2, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
8E8415 SHANK AS-RIPPER
854G, D10N, D10R, D10T, D10T2
1182140 SHANK AS-RIPPER
D10R, D10T, D10T2, D11R
8E8415 SHANK AS-RIPPER
854G, D10N, D10R, D10T, D10T2
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.