AVSPARE.COM
parts catalog

SHEET AS 3157155 - Caterpillar



3157155 SHEET AS Caterpillar parts SHEET
Rating:
21
Alternative (cross code) number:
CA3157155
315-7155
3157155
Caterpillar 3157155 SHEET AS

Buy SHEET AS 3157155 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 38 g00357394
Install O-ring seal (18). Turn housing assembly (11) onto the opposite side. The weight of housing assembly (11) is approximately 680 kg (1500 lb).
Illustration 39 g00357392
Lower the temperature of bearing cup (17). Install bearing cup (17) in the housing assembly.
Illustration 40 g01451665
Attach Tooling (B), Tooling (C), and a suitable lifting device to housing assembly (11). The weight of housing assembly (11) is approximately 680 kg (1500 lb). Install housing assembly (11) onto the torque converter. Install bolts (10).
Illustration 41 g01450330
Lubricate bearing cones (16) with the oil that is being sealed. Install bearing cones (16) onto idler gear (15).
Illustration 42 g01450328
Use two people in order to install idler gear (15) and the shim pack. The weight of idler gear (15) is approximately 36 kg (80 lb).
Illustration 43 g01451687
Lower the temperature of bearing cup (12). Install bearing cup (12) into pump adapter (5).
Illustration 44 g01451688
Attach Tooling (B) and a suitable lifting device to pump adapter (5). The weight of pump adapter (5) is approximately 50 kg (110 lb). Install pump adapter (5) and bolts (6) onto housing assembly (11).
Repeat Steps 52 through 58 in order to adjust bearing end play.
Install lip seal (13) (not shown) and two O-ring seals (14) (not shown) to pump adapter (5) during Step 55.
Illustration 45 g02513136
Install the O-ring seals and manifold (8). Install bolts (7).
Install the O-ring seal and orifice plug (9) (not shown) on housing assembly (11).
Illustration 46 g02505758
Install seal (4) on yoke (1).
Illustration 47 g02505643
Install yoke (1), retainer (3), and bolt (2). Tighten bolt (2) to a torque of 240 25 N m (177 18 lb ft). Note: The following Steps will verify the proper assembly of the torque converter. This Step should be done before the torque converter is installed into the machine.
Illustration 48 g02507416
Apply air pressure to port (114). The air should flow freely through the torque converter. A blockage exists when the air nozzle is pushed backward. The torque converter will need to be repaired before installation into the machine.
Illustration 49 g02507456
For torque converters with a lockup clutch, apply air pressure to port (115). The lockup clutch should engage. A blockage is present when the lockup clutch does not engage. The torque converter will need to be repaired before installation into the machine. End By:
Install the hydraulic fan piston pump.
Install the center implement piston pump.
Install the right-hand implement piston pump.
Install the brake piston pump.
Install the steering piston pump.
Install the transmission pump. Refer to Disassembly and Assembly, "Transmission Pump - Install".
Install the torque converter priority valve.
Install the torque converter outlet relief valve.
Install the torque converter impeller modulating valve.
Install the torque converter lockup clutch modulating valve.
Install the torque converter.


Parts sheet Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.