AVSPARE.COM
parts catalog

SHIELD 4646007 - Caterpillar



4646007 SHIELD Caterpillar parts SHIELD
Rating:
86
Alternative (cross code) number:
CA4646007
464-6007
4646007
Caterpillar 4646007 SHIELD

Buy SHIELD 4646007 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 5
 
  For full view, you need register

Information:

Note: Ensure that the engine is in time. Refer to Testing And Adjusting, "Camshaft Timing".Note: Refer to Testing and Adjusting, "Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting". All of the injectors can be checked or adjusted with the crankshaft positions that are given in the chart. This check will make sure that the pushrod lifters are off the lobes and on the base circles of the camshafts. Refer to the TMI (Technical Marketing Information) for the correct fuel timing dimension to use.
Table 1
Tools Needed
5P-4160 Indicator Contact Point 1
1U-8869 Dial Indicator 1
9U-5138 Setting Gauge 1
9U-5233 Magnetic Fixture Group 1
9S-9082 Engine Turning Tool 1
Illustration 1 g00322956
1U-8869 Dial Indicator
The digital dial indicator needs to be programmed to read actual timing dimensions. Since the 9U-5138 Setting Gauge in the timing and fuel setting tool group is 87.00 mm, set the digital dial indicator for 87.00 mm. Use the following steps in order to program the indicator to read 87.00 mm.
Turn the indicator to the ON position by pushing the "on/off" button.
Push the "in/mm" button so the display shows "mm".
A negative "-" sign should be in the display window under "REV". If that space is blank, push the "+/−" button so the display shows a negative "-" sign. When this is done, the movement of the plunger into the indicator will be displayed. The display will be shown as a negative movement. The movement of the plunger out of the indicator will be displayed as a positive movement.
Push the preset button and hold the preset button down until there is a flashing "P" in the upper right corner of the display. Then release the button.
Push the preset button and hold the preset button down until the flashing "P" disappears and a flashing indicator bar is seen in the lower left corner of the display. Then release the button. Use the preset button so that this position is blank.
Push the preset button and hold the preset button down until the flashing indicator begins flashing under the first number position. The first number position is located in the fourth position to the left of the decimal. Then release the button. Momentarily pushing the preset will cause the display number in that position to change. Use the preset until this position reads zero (0).
Use the preset button to move the flashing indicator and change the display numbers until the display shows 0087.00 mm. Push the preset button and hold the preset button until the flashing "P" is shown in the upper right corner of the display. Release the preset button. Momentarily push the preset button so the flashing "P" and the zeroes to the left of 87.00 mm disappear.
The indicator can now be turned off. The indicator will retain the preset number in memory. To recall the preset number, repeat Steps 1.a through 1.d.
Install a 5P-4160 Indicator Contact Point in the indicator stem.
Install the indicator into the 9U-5233 Magnetic Fixture Group. Leave the collet loose.
Illustration 2 g00323023
Adjustment of fuel timing tools
(1)

Caterpillar parts catalog:

Caterpillar parts catalog
14M Series 3 Motor Grader N9S00001-UP (MACHINE) POWERED BY C13 Engine


Parts shield Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.