AVSPARE.COM
parts catalog

SHROUD AS-FAN 3599375 - Caterpillar



3599375 SHROUD AS-FAN Caterpillar parts 316E L, 318E L SHROUD
Rating:
81
Alternative (cross code) number:
CA3599375
359-9375
3599375
Caterpillar 3599375 SHROUD AS-FAN
Weight: 7 pounds 3 kg.

Buy SHROUD AS-FAN 3599375 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3599375:

EXCAVATOR  316E L   318E L   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Necessary Tools:
A special FT1794 Removal Group is available and needed for this inspection. Two men must work together to do the job.
FT1794 Removal Group 1. Tapping Fixture2. Slotted Bar3. Spacer4. Plate5. Adapter6. BarOther Tools Needed
Removal Of Main Bearing Caps
(1) Use a paper cup, as shown, on the tap. This way the chips will not fall into the crankcase. Turn the tap into tapping fixture (1), until you can see the first threads. (2) Remove both cap bolts from one side of the bearing cap only. Put the tip of the tap into the outside hole, and install tapping fixture (1) as shown. Cut threads approximately 25 mm (1") deep into the outside hole of the cap.(3) Remove the tap and tapping fixture (1). Be careful that no chips fall into the engine. Again, install the inside bolt on the bearing cap.(4) Do the same on the other side of the bearing cap. (5) Fasten an adapter (5) to each end of the bearing cap with 8S4754 Bolts. (6) Fasten a plate (4) to each side of the engine block with two S1594 Bolts. Fasten bar (2) to plates (4) with 7B3235 Bolts and Washers. Fasten bars (6) to adapters (5) and bars (2) with S1621 Bolts and washers. On front and rear main bearings, use spacers (3) between bars (6) and adapters (5) with 2B94 Bolts.(7) When this installation of tools is complete on both sides, remove the inside bearing cap bolts. (8) There must be one man on each side of the engine, and they must work together. In this way, they can now lower the bearing cap with bars (2), until the cap is at the end of slot (7).(9) Inspect the bearings.(10) To install the bearing cap again, two men must work together, one on each side of the engine. To pull the cap up into place, use the slotted bars (2) again. The cap must start into the block on both sides at the same time.(11) Install the inside bearing cap bolts.(12) Remove the tools. Install the outside cap bolts. Tighten all cap bolts to the correct torque. See specifications in the Service Manual.

Caterpillar parts catalog:

Caterpillar parts catalog
316F L Excavator YDL00001-UP (MACHINE) POWERED BY C4.4 Engine
318F L Excavator FFT00001-UP (MACHINE) POWERED BY C4.4 Engine
316F L Excavator ECZ00001-UP (MACHINE) POWERED BY C4.4 Engine
318F L Excavator HCP00001-UP (MACHINE) POWERED BY C4.4 Engine
316F L Excavator XAD00001-UP (MACHINE) POWERED BY C4.4 Engine
316E L Excavator DZW00001-UP (MACHINE) POWERED BY C4.4 Engine
316E L Excavator YZZ00001-UP (MACHINE) POWERED BY C4.4 Engine
316E L Excavator WZY00001-UP (MACHINE) POWERED BY C4.4 Engine
318E L Excavator WZS00001-UP (MACHINE) POWERED BY C4.4 Engine
318E L Excavator DZF00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts shroud Caterpillar catalog:

3599376 SHROUD
316E L, 318E L
3551356 SHROUD AS
311D LRR, 312D, 312D L, 313D
2813631 SHROUD AS
311D LRR, 312D, 312D L
2676491 SHROUD
M313D, M315D, M315D 2, M317D 2, M318D MH
2585137 SHROUD
M313D, M315D, M315D 2, M316D, M317D 2, M318D, M318D MH, M322D, M322D MH
3599376 SHROUD
316E L, 318E L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.