AVSPARE.COM
parts catalog

SHROUD 9V9546 - Caterpillar



9V9546 SHROUD Caterpillar parts 916, 926A, 936, 950B, CS-643, IT18, IT28 SHROUD
Rating:
35
Alternative (cross code) number:
CA9V9546
9V-9546
9V9546
Caterpillar 9V9546 SHROUD
Weight: 0.50 pounds 0 kg.

Buy SHROUD 9V9546 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 9V9546:

INTEGRATED TOOLCARRIER  IT18   IT28  
VIBRATORY COMPACTOR  CS-643  
WHEEL LOADER  916   926A   936   950B   Caterpillar
Number on catalog scheme: 14
 
  For full view, you need register

Information:

27. Remove race (36) from the cam. 28. Remove rollers (37) and springs (38) from cam (39). 29. Remove ring (40) and race (41) from the stator. 30. Remove cam (39) from the stator. 31. Remove retainer (42), bearing (43) and the race from the torque converter. 32. Put housing (44) and the turbine in position on a press. The weight of the housing and turbine are 41 kg (90 lb).33. Use a press and tool (C) to remove turbine from housing (44). 34. Remove bolts (45) and hub (46) from the turbine. 35. Remove rings (47) and (48) from hub (46). 36. Remove ring (49) from the housing. 37. Remove plate (50) from the housing. 38. Remove disc (51) from the housing. 39. Install two 1/4" - 20 NC eyebolts (53) in piston (52) as shown.40. Remove piston (52) from the housing. 41. Remove ring (54) from the piston. 42. Remove ring (55) from the housing. 43. Use a press and tool (D) to remove the bearing from the housing.Assemble Torque Converter
Before the torque converter is assembled, see Specifications for correct clearances. These clearances must be correct for the torque converter to operate with efficiency. Use acceptable inside and outside micrometers and other necessary equipment to measure the components.
1. Install ring (55) in the housing. 2. Install ring (54) on piston (52). 3. Install two 1/4" - 20 NC eyebolts (56) in piston (52) as shown.4. Install piston (52) in the housing as shown. 5. Install disc (51) in the housing. 6. Install ring (57) and ring (49) in the housing. 7. Install ring (47) and ring (48) in the hub. 8. Install hub (46) on turbine (58) with bolts (45). Tighten the bolts to a torque of 49 3 N m (36 2 lb ft). 9. Install turbine (58) in the housing. Make sure the hub and the disc are in alignment. 10. Install race (59), retainer (42) and bearing (43) in the turbine.11. Heat the stator to a maximum temperature of 135°C (275°F) for approximately four minutes and lower the temperature of cam (39). There is an identification on the cam that shows "impeller side". Make sure when the cam is installed in the stator that the impeller side of the cam will face the impeller in the housing. 12. Install cam (39) in the stator. 13. Install race (41) and ring (40) on the stator. 14. Install race (36) in the stator. 15. Install springs (38) and rollers (37) in the cam with the springs in the deeper part of each cam groove as shown. The springs must be installed with the maximum number of loops toward the outside (cam side). After the springs and rollers are installed, the stator must turn freely in a counterclockwise direction but not in a clockwise direction. If the stator does not turn counterclockwise, the springs and rollers have been installed incorrectly. 16. Install race (35) and ring (34) on the stator. 17. Install stator (33)

Caterpillar parts catalog:

Caterpillar parts catalog
IT28 INTEGRATED TOOLCARRIER 8JB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT28B INTEGRATED TOOLCARRIER 5SD00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
950E WHEEL LOADER 63R06054-UP (MACHINE) POWERED BY 3304 ENGINE
IT28B INTEGRATED TOOLCARRIER 5SD00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
936E WHEEL LOADER 45Z03057-UP (MACHINE) POWERED BY 3304 ENGINE
926E WHEEL LOADER 4NB02076-UP (MACHINE) POWERED BY 3204 ENGINE
CS-643, CP-643, CS-653, CP-653 VIBRATORY COMPACTOR 7FD00001-UP (MACHINE) POWERED BY 3304 ENGINE
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
950E WHEEL LOADER 63R06054-UP (MACHINE) POWERED BY 3304 ENGINE
IT28B INTEGRATED TOOLCARRIER 5SD00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
936E WHEEL LOADER 45Z03057-UP (MACHINE) POWERED BY 3304 ENGINE
926E WHEEL LOADER 4NB02076-UP (MACHINE) POWERED BY 3204 ENGINE
950E WHEEL LOADER 63R06054-UP (MACHINE) POWERED BY 3304 ENGINE
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE


Parts shroud Caterpillar catalog:

4V8182 SHROUD
916, 926, 936, 936F, 950B, 950B/950E, 950F, 950F II, 966D, 966F, 966F II, 980C, 980F, G936, IT28B
7V5200 SHROUD
916, 926, 936, 936F, 950B, 950B/950E, 966D, G936, IT28B
6W0151 SHROUD-FRONT
916, 926, 936, G936, IT28
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.