3967436 SNOW AR-MOTOR GRADER Caterpillar parts
140M
Rating:
Alternative (cross code) number:
CA3967436
396-7436
3967436
CA3967436
396-7436
3967436
MOTOR GRADER,
Compatible equipment models: 3967436:
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the left engine enclosure. Refer to Disassembly and Assembly, "Left Engine Enclosure - Remove".
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
At operating temperature, the hydraulic oil is hot and under pressure. Hot oils can cause burns.To prevent possible personal injury, release the pressure in the work tool hydraulic circuit (boom, stick, bucket, and swing), travel circuits, and the hydraulic oil tank at the filler cap before any hydraulic lines or components are disconnected or removed.Remove the filler cap only when the engine is stopped and the filler cap is cool enough to touch.
Illustration 1 g00849446
Remove the cap from the hydraulic tank. Attach Tooling (A) to the hydraulic tank. Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system. This will minimize the leakage from the tubes and the lines.
Illustration 2 g00849389
Loosen bolts (1). Remove bolts (2) and sheet assembly (3).
Illustration 3 g00849395
Loosen bolts (6). Remove bolts (4) and sheet assembly (5).
Illustration 4 g00849405
Disconnect hose assemblies (7), (8), (9), and (10).
Illustration 5 g00849412
Support fan drive motor (11) with a lifting sling and a hoist. Remove bolts (12) and the fan drive motor. The weight of fan drive motor (11) is approximately 28 kg (60 lb). Installation Procedure
Illustration 6 g00849412
Use a lifting sling and a hoist to position fan drive motor (11). Install bolts (12). The weight of fan drive motor (11) is approximately 28 kg (60 lb).
Illustration 7 g00849405
Connect hose assemblies (7), (8), (9), and (10).
Illustration 8 g00849395
Position sheet assembly (5) and install bolts (4). Tighten bolts (6).
Illustration 9 g00849389
Position sheet assembly (3) and install bolts (2). Tighten bolts (1).
Illustration 10 g00849446
Remove Tooling (A) from the hydraulic tank and install the cap on the hydraulic tank. End By:
Install the left engine enclosure. Refer to Disassembly and Assembly, "Left Engine Enclosure - Install".
Start By:
Remove the left engine enclosure. Refer to Disassembly and Assembly, "Left Engine Enclosure - Remove".
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
At operating temperature, the hydraulic oil is hot and under pressure. Hot oils can cause burns.To prevent possible personal injury, release the pressure in the work tool hydraulic circuit (boom, stick, bucket, and swing), travel circuits, and the hydraulic oil tank at the filler cap before any hydraulic lines or components are disconnected or removed.Remove the filler cap only when the engine is stopped and the filler cap is cool enough to touch.
Illustration 1 g00849446
Remove the cap from the hydraulic tank. Attach Tooling (A) to the hydraulic tank. Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system. This will minimize the leakage from the tubes and the lines.
Illustration 2 g00849389
Loosen bolts (1). Remove bolts (2) and sheet assembly (3).
Illustration 3 g00849395
Loosen bolts (6). Remove bolts (4) and sheet assembly (5).
Illustration 4 g00849405
Disconnect hose assemblies (7), (8), (9), and (10).
Illustration 5 g00849412
Support fan drive motor (11) with a lifting sling and a hoist. Remove bolts (12) and the fan drive motor. The weight of fan drive motor (11) is approximately 28 kg (60 lb). Installation Procedure
Illustration 6 g00849412
Use a lifting sling and a hoist to position fan drive motor (11). Install bolts (12). The weight of fan drive motor (11) is approximately 28 kg (60 lb).
Illustration 7 g00849405
Connect hose assemblies (7), (8), (9), and (10).
Illustration 8 g00849395
Position sheet assembly (5) and install bolts (4). Tighten bolts (6).
Illustration 9 g00849389
Position sheet assembly (3) and install bolts (2). Tighten bolts (1).
Illustration 10 g00849446
Remove Tooling (A) from the hydraulic tank and install the cap on the hydraulic tank. End By:
Install the left engine enclosure. Refer to Disassembly and Assembly, "Left Engine Enclosure - Install".
Caterpillar SIS machinery equipment:
Parts snow Caterpillar catalog:
3500677
SNOW AR-MOTOR GRADER
140M, 160M
140M, 160M