AVSPARE.COM
parts catalog

SPACER 7B0297 - Caterpillar



7B0297 SPACER Caterpillar parts SPACER
Rating:
16
Alternative (cross code) number:
CA7B0297
7B-0297
7B0297
Caterpillar 7B0297 SPACER

Buy SPACER 7B0297 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 253-3272 Cylinder 2
B(2) 178-9312 Hose As 2
C(3) 253-3276 Distribution Coupler 1
185-0683 Gauge As 1
D(4)(5) 227-6724 Electric Hydraulic Pump Gp (120 V) 1
227-8834 Electric Hydraulic Pump Gp (240 V) 1
191-5347 Hydraulic Pump Gp 1
156-7167 Manual Hydraulic Pump 1
E 279-3473 Engine Turning Tool 1
329-3831(6) Air Power Turning Tool 1
F 369-4007 Bearing Driver 1
G - Guide Stud M20 - 2.5 by 250 MM 2
(1) Part of Tool Group 278-1150
(2) Part of Tool Group 278-1150
(3) Part of Tool Group 278-1150
(4) Use any of the pumps that are listed in Tooling (D) for this procedure.
(5) The latest pumps and hoses require 22000 psi capacity.
(6) OptionalStart By:
Remove the starting motors. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove" or Disassembly and Assembly, "Air Starting Motor - Remove".
Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove".
Remove the fuel pump. Refer to Disassembly and Assembly, "Fuel Pump - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
Remove the engine oil scavenge pump. Refer to Disassembly and Assembly, "Engine Oil Scavenge Pump - Remove".
Illustration 1 g01212026
Remove bolts (1) and remove side cover (2). Repeat for the remaining side covers on both sides of the engine.
Illustration 2 g01212105
Install Tooling (A) onto the studs for the crankshaft main bearing cap. Tighten the threaded collar of Tooling (A). Loosen the threaded collar of Tooling (A) by 1 1/2 turns. Attach Tooling (B) onto Tooling (A). Attach Tooling (B) onto Tooling (C). Attach Tooling (C) onto Tooling (D). Apply approximately 135 MPa (19580 psi) of pressure to Tooling (A). Use the drive on Tooling (A) in order to loosen the nuts for the crankshaft main bearings. Rotate the drive on Tooling (A) by approximately three turns. Release the pressure on Tooling (A). Remove Tooling (A).
Illustration 3 g01212278
Remove bolt (5) from each side of the engine and install Tooling (G).
Illustration 4 g01212274
Remove crankshaft main bearing nuts (3). Remove plate (4).
Illustration 5 g01212288
Slide down crankshaft main bearing cap (6) on the studs. Remove crankshaft main bearing (7) from crankshaft main bearing cap (6).
Install Tooling (F) in order to remove the upper crankshaft main bearing. If necessary, use Tooling (E) in order to rotate the crankshaft and remove the upper crankshaft main bearing.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.