AVSPARE.COM
parts catalog

SPECIAL AR 3157345 - Caterpillar



3157345 SPECIAL AR Caterpillar parts SPECIAL
Rating:
76
Alternative (cross code) number:
CA3157345
315-7345
3157345
Caterpillar 3157345 SPECIAL AR

Buy SPECIAL AR 3157345 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g02599016
Connections of the Main Power RelayThis diagnostic code is associated with the Main Power Relay. The FMI 03 diagnostic code is activated when the Transmission ECM detects an above normal voltage of the relay circuit. This diagnostic code is activated on the ECM via CAN Data Link.The following conditions could cause this diagnostic code to be activated:
The relay has failed.
The relay circuit is shorted to a power source.
The ECM has failed. This condition is unlikely.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, that all connections are secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE RELAY FOR A SHORT
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector from the relay. Disconnect the machine harness connector J2 from the ECM.
At the machine harness connectors for the Relay Driver Module, measure the resistance between contact J2-3 (wire 306-GN) and each of the other circuits that are used in the J2 connector for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The resistance measurements do not indicate a short to another circuit in the machine harness. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. Repair: The short is between wire 306-GN and the circuit that measured a low resistance measurement.For information on testing for short circuits and finding short circuits, refer to Testing and Adjusting, "Wiring Harness (Short Circuit) - Test". Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECMThe disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the relay and the ECM remain disconnected.
At the machine harness connector J2 for the ECM, use a 151-6320 Removal Tool to remove the relay wire 306-GN and the socket at contact J2-3 from the harness connector.
Reconnect the machine harness J2 connector to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active CID 3467 FMI 03 diagnostic code.Expected Result:The CID 3467 FMI 03 diagnostic code is no longer active. A CID 3467 FMI 05 diagnostic code is now active.Results:
OK - The CID 3467 FMI 03 diagnostic code is no longer active. A CID 3467 FMI 05 diagnostic code has become active after the relay circuit is disconnected. The ECM has


Parts special Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.