AVSPARE.COM
parts catalog

SPOOL 9W0612 - Caterpillar



9W0612 SPOOL Caterpillar parts D4H SPOOL
Rating:
69
Alternative (cross code) number:
CA9W0612
9W-0612
9W0612
Caterpillar 9W0612 SPOOL
Weight: 0.100 pounds 0 kg.

Buy SPOOL 9W0612 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 9W0612:

TRACK-TYPE TRACTOR  D4H   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

Below 0°C (32°F)
1. Follow the steps on preceding pages under "Power Shift" or "Direct Drive," depending on which transmission the machine has, before going to step 2 below. 2. Turn the start switch knob to START. 3. Push the starting aid (ether) button IN and release.4. Use additional starting fluid every two seconds until the engine starts.
Inject starting aid (ether), only while cranking the engine. Use sparingly, excessive ether without cranking can cause piston and ring damage.Wait approximately two seconds before injecting again.Use ether for cold starting purposes only.After every 30 seconds of engine cranking, allow 2 minutes for the starting motor to cool before cranking again.
5. Release the start switch knob when the engine starts.For starting below -18°C (0°F), use of additional cold weather starting aids is recommended. A coolant, fuel or oil heater or extra battery capacity may be required.At starting temperatures below -23°C (-10°F), consult your Caterpillar dealer or refer to the "Operation, Lubrication and Maintenance Guide for Cold Weather Operation," Caterpillar Form SEBU5898.Precombustion Engine
Above 16°C (60°F)
1. Follow the steps on preceding pages under "Power Shift" or "Direct Drive," depending on which transmission the machine has, before going to step 2 below. 2. Turn the heat-start switch knob left to HEAT for the indicated time as shown in the chart below. 3. Turn the switch knob to START and release the switch knob after the engine starts.4. After the engine starts, it may be necessary to turn the switch knob to HEAT again, until the engine runs smooth.
After every 30 seconds of engine cranking, allow 2 minutes for the starting motor to cool before cranking again. Do not turn start switch knob to HEAT when the engine is hot and running.
For starting below -18°C (0°F), use of additional cold weather starting aids is recommended. Coolant, fuel or oil heater or extra battery capacity may be required.At temperatures below -23°C (-10°F), consult your Caterpillar dealer, or refer to the Cold Weather Operation Guide, Form SEBU5898, available from your Caterpillar dealer.Starting Fluid and Heat-Start
Ether is poisonous and flammable. Do not store replacement ether cylinders in living areas or in the operator's compartment.Do not smoke while changing ether cylinders.Use ether only in well ventilated areas.Use it with care to avoid fires.Keep the cylinders out of the reach of unauthorized personnel.Avoid breathing ether vapors or repeated contact of ether with the skin.Do not store cylinders in direct sunlight.Do not puncture or burn the cylinders.Discard the cylinders in a safe place.
1. Follow the step on preceding pages under "Power Shift" or "Direct Drive," depending on which transmission the machine has, before going to step 2 below. 2. Turn the heat-start switch knob left to HEAT for the indicated time as shown in the chart below. 3. Turn the switch knob to START and discharge a starting aid capsule or spray starting fluid for approximately one second into the precleaner while cranking the engine.Wait approximately 2 seconds before spraying again.
Use ether sparingly. Spray ether into the air intake for approximately one

Caterpillar parts catalog:

Caterpillar parts catalog
D4H & D4H LGP TRACTORS / POWERSHIFT / 8PB00001-03999 (MACHINE) POWERED BY 3204 ENGINE
D4H & D4H LGP TRACTORS / DIRECT DRIVE / 2AC00001-03999 (MACHINE) POWERED BY 3204 ENGINE


Parts spool Caterpillar catalog:

3T9939 SPOOL
578, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H XR, D7H, D7R, D8R
3T9949 SPOOL
578, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H XR, D7H, D7R, D8R
3T9937 SPOOL-SELECTOR
578, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D7H, D7R, D8R
9W4251 SPOOL
578, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5HTSK II, D6H, D6H XL, D6H XR, D7H, D7R, D8R
7T3972 SPOOL
578, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H XR, D7H, D7R, D8R
3P4660 SPOOL-VALVE
55, 578, D10N, D10R, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D6D, D6H, D6H XL, D6H XR, D7G, D7H, D7R, D8R
7T5644 SPOOL AS
517, 527, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II
6T2997 SPOOL
527, D4H, D5H, D5H XL, D5HTSK II
7G9563 SPOOL
517, 527, 561M, 611, 613C, 613C II, 613G, 615, 615C, 814B, 815B, 826C, 910, 916, 926, 931B, 933, 935C, 936, 936F, 950B, 950B/950E, 950F, 950F II, 966D, 966F, 980C, 980F, 983B, 988B, 992C, D10, D250E, ...
6T4254 SPOOL-SPEED SELECTOR
517, 527, 561M, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6M
6P7174 SPOOL
528, 769C, 931B, D4H, D6H, D6H XL, D6H XR
6Y6563 SPOOL AS
517, 527, D10N, D11N, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5HTSK II, D9R
6P5088 SPOOL
980C, 983B, 988B, 992C, D10, D44B
6Y1393 SPOOL
D8N, D8R, D9R
9W6577 SPOOL
D8N, D8R, D8R II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.