AVSPARE.COM
parts catalog

SPRING 1C4037 - Caterpillar



1C4037 SPRING Caterpillar parts SPRING
Rating:
26
Alternative (cross code) number:
CA1C4037
1C-4037
1C4037
Caterpillar 1C4037 SPRING
Weight: 2 pounds 0 kg.

Buy SPRING 1C4037 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Jackstand Parts
Specifications
Capacity: 79.5 tons each. Maximum operating pressure: 68900.00 kPa (10000 psi). Height Range:Short Extension - 584 mm (23") to 914 mm (36")Long Extension - 965 mm (38") to 1270 mm (50")Auxiliary Extension - 1270 mm (50") to 1524 mm (60")Jack cylinder stroke - 330 mm (13")Positive lockup range - 318 mm (12.5") Weight:Base - 158 kg (348 lb).Short Extension - 54 kg (119 lb).Long Extension - 101 kg (223 lb).Auxiliary Extension - 9 kg (19 lb). Base Dimensions: 635 mm (25") × 965 mm (38"). Standard Pump Motor:Single Phase 115/230 v. 11 Amp @ 230 v.Three Phase 230/460 v. motor available. 6.5 Amp @ 230 v. Motor Size: 1.5 kW (2 hp). Pump Flow:6 L (380 cu in)/min. @ 0 to 10335 kPa (0 to 1500 psi)1 L (65 cu in)/min. @ 10335 to 68900 kPa (1500 to 10000 psi). Reservoir Capacity: 11.4L (3.0 gal).Specify required wiring and plug on order.Operating Instructions
1. Read and observe all precautions concerning assembly, maintenance, and operation of the hydraulic system. Instructions are provided with the hydraulic pump and with the cylinder used in this unit.Contact Caterpillar Service Technology Group if such literature is missing or additional copies are needed.Jackstands shown above are in the shortest and tallest configuration, connected in parallel to the 4C5809 Pump Group.Each jackstand can lift 72186 kg (159000 lb) with the pump pressure at 68900 kPa (10000 psi). Power two jackstands with one 4C5809 Pump Group (10) and the 4C5807 Tee Connection (9) to lift one side or end of very heavy vehicles. This minimizes local stresses on the vehicle and provides best stability when the load is on the stands.Control the rate of lift for each jack using needle valves (25) in the Tee connection group.A single jackstand can be connected to the pump when load and stability requirements are lower. (The jack lifting speed will double.)* Be sure hoses and connections are undamaged and properly tightened before applying hydraulic pressure.* If necessary, use spacers (7) under the load cap (29) to extend the auxiliary extension a MAXIMUM of 254 mm (10") before starting to lift the load.* Lift the load no higher than necessary. Excessively high lifts usually result in greater side loading and reduced stability.* Control the lift rates with needle valve (25) when using parallel connection.* Place jackstands only at recommended points.* Never attempt to lift a load with stand transport wheels extended.* When the load is lifted to desired height, secure it with the two double pins (4) through column and extension.* NEVER leave the load on the stands without the locking pins installed.* Lower the load SLOWLY. Sudden release of hydraulic pressure will activate the fluid velocity valves, locking oil in the jack cylinders. Apply pressure to the cylinders to unlock the valves.* Lower the jackstand extensions fully after use. A special valve in the pump aids retraction of unloaded jack cylinders.* Before moving the jackstand to a new location, the long extension should be fully retracted to avoid the possibility


Parts spring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.