AVSPARE.COM
parts catalog

SPRING-RETURN 4644967 - Caterpillar



4644967 SPRING-RETURN Caterpillar parts SPRING
Rating:
16
Alternative (cross code) number:
CA4644967
464-4967
4644967
Caterpillar 4644967 SPRING-RETURN
Weight: 0.05 pounds 0 kg.

Buy SPRING-RETURN 4644967 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01321348
Schematic for the Winch Drive Away SwitchThe Winch Drive Away Switch has two inputs to the ECM. The two inputs are normally open and normally closed. During normal operation, one of the inputs is open. The other input is grounded. When a circuit is measured with a voltmeter, an open circuit will measure approximately 13 DCV to ground and a closed circuit will measure approximately 0 DCV to ground. An FMI 03 diagnostic code is recorded when the status of both the inputs are open.The possible causes of this diagnostic code are listed below:
The return circuit (wire 202-BK) is open.
Switch contact "1" signal circuit (wire P781-GY) is permanently open.
Switch contact "3" signal circuit (wire P782-PK) is permanently open.
The switch has failed.
The ECM has failed. This is unlikely. Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.
Table 1
Status of the Switch    
MODE    Switch Position    J1-27 (N/O)
P782-PK Circuit    J1-26 (N/C)
P781-GY Circuit    
Released     Up     Open     Closed    
Pressed     Down     Closed     Open    System Response:A level 1 warning will be generated.Note: Ensure that the diagnostic code CID 2481 - FMI 03 is active before performing this procedure.Test Step 1. CHECK THE GROUND CIRCUIT FOR AN OPEN
Turn the disconnect switch and the key switch to the OFF position.
Disconnect the machine harness connectors from the ECM.
Disconnect the switch from the machine harness.
Measure the resistance between chassis ground and contact 2 (wire 202-BK) at the connector for the switch.Expected Result:The resistance should be less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. Proceed to Test Step 2.
NOT OK - The resistance is greater than 5 ohms.Repair: The return circuit (wire 202-BK) is open in the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE SWITCH
Check for continuity between contact 1 and contact 2 of the switch.
Press the switch and then release the switch while checking for continuity.
Check for continuity between contact 2 and contact 3 of the switch.
Press the switch and then release the switch while checking for continuity.Expected Result:The continuity check agrees with the preceding Table.Results:
OK - The continuity check agrees with the preceding Table. Proceed to Test Step 3.
NOT OK - The continuity check does not agree with the preceding Table. The switch has failed.Repair: Replace switch. Verify that the new switch corrects the diagnostic code.STOPTest Step 3. CHECK THE SIGNAL CIRCUITS FOR AN OPEN
Reconnect the switch to the machine harness.
The machine harness connectors remain disconnected from the ECM.
At the machine harness connector for the ECM, check for continuity between contact J1-27 (wire P782-PK) and frame ground.
Press the switch and then release the switch while


Parts spring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.