AVSPARE.COM
parts catalog

SPRING-COLLAR 4646176 - Caterpillar



4646176 SPRING-COLLAR Caterpillar parts SPRING
Rating:
21
Alternative (cross code) number:
CA4646176
464-6176
4646176
Caterpillar 4646176 SPRING-COLLAR
Weight: 0.01 pounds 0 kg.

Buy SPRING-COLLAR 4646176 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01324428
Schematic for the Pilot Pressure Supply Solenoid ValveThis diagnostic code is recorded when the ECM detects an incomplete electrical path. The electrical path from the ECM to the solenoid back to the ECM is incomplete.The possible causes for this diagnostic code are listed:
The signal circuit from the ECM to the solenoids is open.
The return circuit from the solenoid is open.
The internal windings for the solenoid have high impedance.
The internal windings for the solenoid are open.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position.
Disconnect the solenoid with the diagnostic code from the harness.
Observe the ON/OFF status of the diagnostic code indicator.
At the harness connector for the solenoid, place a jumper wire between contact 1 (wire E918-GN) and contact 2 (wire H708-OR).Expected Result:The diagnostic code indicator remains active.Results:
YES - The diagnostic code indicator remains active and the diagnostic code remains active. The harness has failed or the ECM has failed. Proceed to Test Step 2.
NO - The diagnostic code indicator is inactive.Repair: The solenoid valve has failed. Repeat this test in order to verify the failure. Repair the solenoid or replace the solenoid. Repair the connecting harness or replace the connecting harness at the solenoid.STOPTest Step 2. CHECK THE HARNESS.
Turn the disconnect switch to the OFF position.
Remove the jumper wire from contact 1to 2.
Reconnect the solenoid valve to the harness.
Disconnect the harness from the ECM.
At the harness connector for the ECM, measure the resistance between contacts J2-4 (wire H708-OR) and contact J2-2 (wire E918-GN).Expected Result:The resistance is greater than 5000 Ohms (no continuity).Results:
YES - The resistance is greater than 5000 Ohms (no continuity).Repair: The harness circuit has failed. Wire H708-OR is open in the harness between the ECM and the solenoid valve, or the wire E918-GN to the solenoid valve is open. Repair the harness or replace the harness.STOP
NO - The resistance is less than 5000 Ohms.Repair: Check the circuit again.If the cause of the problem is not found, contact the Technical Communicator for your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, see Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP


Parts spring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.