AVSPARE.COM
parts catalog

STARTING MOTOR GP-ELECTRIC 3534500 - Caterpillar



3534500 STARTING MOTOR GP-ELECTRIC Caterpillar parts C9.3 STARTING
Rating:
17
Alternative (cross code) number:
CA3534500
353-4500
3534500
Caterpillar 3534500 STARTING MOTOR GP-ELECTRIC

Buy STARTING MOTOR GP-ELECTRIC 3534500 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE,

Compatible equipment models: 3534500:

INDUSTRIAL ENGINE  C9.3   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 2 g01558614
Attach a suitable lifting device to the head end of bucket cylinder (1). Use the suitable lifting device to raise bucket cylinder (1) until bucket cylinder (1) is level.
Illustration 3 g01558633
Disconnect two hose assemblies (4) from bucket cylinder (1).
Remove nuts and retaining bolt (6). Remove pin (5). Remove bucket cylinder (1).
Remove the shims that are used at the pin joint for the bucket cylinder. Disassembly and Assembly Information
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed.Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death.Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
Illustration 4 g01558636 (1) Torque for locknut ... 1650 85 N m (1220 65 lb ft)Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0960 Grease Cartridge 1 Note: Check O-ring seals for wear or for damage. Replace the components, if necessary.
Be sure that the pin bores in the stick, in the link assemblies, and in the bucket cylinder are clean and free of dirt prior to installation of the bucket cylinder.
Illustration 5 g01558614
Use a suitable lifting device to position bucket cylinder (1) on the stick. The weight of bucket cylinder (1) is approximately 50 kg (110 lb). Make sure that the grease fittings in the head end and in the rod end of the bucket cylinder are facing away from the stick.
Illustration 6 g01558653
Illustration 7 g00535067
Top View Of Stick And Bucket Cylinder
Slide bucket cylinder (1) to one side until bucket cylinder (1) makes contact with the stick. Measure the total clearance between bucket cylinder (1) and the stick at the pin bore. The total clearance of Measurement (a) plus Measurement (b) must not be more than 1.0 mm (0.04 inch). If the total clearance is less than 1.0 mm (0.04 inch), the addition of shims between the bucket cylinder and stick will not be required. Apply Tooling (A) on pin (5) and install pin (5). Install retaining bolt (6) and the nuts.
If the total clearance is more than 1.0 mm (0.04 inch), the addition of shims between the bucket cylinder and the stick will be required. Install the shims between the stick and the bucket cylinder. The shims should be installed on the side of the retaining bolt. Apply Tooling (A) on pin (5) and install the pin. Install retaining bolt (6) and the two nuts.
Illustration 8 g01558593
Illustration 9 g00357378
Lower the rod end of bucket cylinder (1) between the link assemblies. Apply Tooling (A) on pin (3) and install the pin (3). Install retaining bolt (2) and the nuts.
Rotate pin (3) until the retaining bolt is parallel with the link assembly. Tighten the outside nut until the nut is 0.5 mm (0.02 inch) beyond the end of the retaining bolt. Tighten the inside nut against the outside nut to a torque of 70 15 N m (50 10 lb ft).
Illustration 10 g01558673
Connect two hose assemblies (4) to bucket cylinder (1).
Remove the

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts starting Caterpillar catalog:

2071551 STARTING MOTOR GP-ELECTRIC
3116, 3126, 3126B, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325B, 325B L, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 32...
6V4215 STARTING MOTOR GP-ELECTRIC
C-9, C9, C9.3, CX31-C9I, TH31-E61
2071524 STARTING MOTOR GP-ELECTRIC
3196, 3406B, 3406E, 480, 75C, 75D, 85C, 85D, C-10, C-12, C-9, C11, C12, C13, C15, C18, C9, C9.3, CPT372, CX31-C13I, CX31-C18I, CX31-C9I, CX35-C18I, MTC735, SUF557, TH31-E61, TH35-C11I, TH35-C13I, TH35...
2071537 STARTING MOTOR GP-ELECTRIC
3176C, 3196, 3406B, 3406C, 3406E, C-10, C-12, C-9, C11, C12, C13, C15, C18, C9, C9.3, CPT372, CX31-C13I, CX31-C9I, SUF557, TH31-E61, TH35-C11I, TH35-C13I, TH35-C13T
6V3948 STARTING MOTOR GP-ELECTRIC
1673C, 3208, 3304, 3306, 3306B, 65C, 70C, C-9, C9, C9.3, CX31-C9I, G3304, G3306, TH31-E61
2493681 STARTING MOTOR GP-ELECTRIC
C13, C9, C9.3, CX31-C13I, CX31-C9I, TH31-E61, TH35-C13I
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.