AVSPARE.COM
parts catalog

STATOR GP-MAIN 4646061 - Caterpillar



4646061 STATOR GP-MAIN Caterpillar parts STATOR
Rating:
76
Alternative (cross code) number:
CA4646061
464-6061
4646061
Caterpillar 4646061 STATOR GP-MAIN

Buy STATOR GP-MAIN 4646061 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:

Removal Procedure
Illustration 1 g02909057
Loosen the hose clamp and disconnect the hose assembly from elbow (3).
Slide the locking tab into the unlocked position and disconnect harness assembly (1) from throttle valve (2).
Loosen hose clamp (6) and disconnect hose assembly (7) from elbow (3).
Remove plug (4) from elbow (3). Remove sealing washer (5) (not shown) from the plug.
Illustration 2 g02909137
Illustration 3 g02909198
Remove nuts (9) from studs (13).
Remove bolts (8). Note: Bolt (8) in Position (X) must be removed with air inlet elbow (3) in order to prevent the bolt from falling into the induction system.
Remove gasket (12).
Remove throttle valve (2) from studs (13).
Remove gasket (14) (not shown).
If necessary, remove adaptor (11) and sealing washer (10) from elbow (3).
If necessary, remove studs (13). Refer to Disassembly and Assembly, "Inlet Manifold - Remove and Install" for the correct procedure. Installation Procedure
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 4 g02909198
Illustration 5 g02909137
If necessary, install studs (13). Refer to Disassembly and Assembly, "Inlet Manifold - Remove and Install" for the correct procedure.
Install gasket (14) (not shown) onto studs (13).
If necessary, follow Step 4.a through Step 4.b in order to install adaptor (11).
Install new sealing washer (10) to adaptor (11).
Install adaptor assembly (11) to air inlet elbow (3). Tighten the adaptor to a torque of 20 N m (177 lb in).
Install throttle valve (2) onto studs (13).
Install gasket (12) onto studs (13).
Illustration 6 g02909057
Install bolt (8) in Position (X) to elbow (3). Install elbow (3) onto studs (13) and tighten bolt (8) in Position (X) finger tight. Install remaining bolt (8).
Install nuts (9) to studs (13).
Tighten bolts (8) and nuts (9) to a torque of 10 N m (89 lb in).
Install new sealing washer (5) (not shown) to plug (4).
Tighten the plug to a torque of 50 N m (37 lb ft).
Install the clamp to the air inlet hose and connect the air inlet hose to air inlet elbow (3).
Connect harness assembly (1) onto throttle valve (2). Slide the locking tab into the locked position.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
G3512 Generator Set E2P00001-UP
G3512 Generator Set E2T00001-UP
C32 Generator Set FLX00001-UP
C27 Generator Set 2A300001-UP
3512 Generator Set LNF00001-UP
3512B Generator Set LY800001-UP
3512 Generator Set LY700001-UP
C32 Generator Set JTW00001-UP
C32 Generator Set PAE00001-UP
C32 Generator Set for LRC NRC00001-UP
3512 Generator Set ZAF00001-UP
C32 Generator SET JSJ00001-UP
3512 Generator Set YAK00001-UP
C32 Generator Set JAZ00001-UP
3512 Generator Set YBA00001-UP
3512 Generator Set JM200001-UP
C32 Generator Set JTW00001-UP
C32 Generator Set P7E00001-UP


Parts stator Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.