AVSPARE.COM
parts catalog

STEP GP 3967742 - Caterpillar



3967742 STEP GP Caterpillar parts 901C, 902C, 903C STEP
Rating:
25
Alternative (cross code) number:
CA3967742
396-7742
3967742
Caterpillar 3967742 STEP GP

Buy STEP GP 3967742 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT WHEEL LOADER,

Compatible equipment models: 3967742:

COMPACT WHEEL LOADER  901C   902C   903C   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 2 g01623868
Tooling (B)
Table 2
Required Tools    
Tooling    Item    Part
Number    Description    Qty    
A     A1     8T-0855     Pressure Gauge
4000 kPa (580 psi)     1    
A2 6V-3989     Fitting     1    
A3 6V-4143     Coupler     2    
A4 177-7861     Hose As
41368 kPa (6000 psi)     1    
B     B1     198-4234     Digital Indicator     1    
B2 198-4239     Pressure Sensor Gp (
41368 kPa (6000 psi))     1    
B3 198-4236     Adapter Cable As Coupler     1    Test Preparation
Move the machine to a smooth horizontal location.
Permit only one operator on the machine. Keep all other personnel away from the machine or in the sight of the operator.
Place the steering control lever in the NEUTRAL position.
Engage the parking brake.
Lower the attachments to the ground.
Stop the engine.
Turn the key to the ON position, but do not start the engine.
Verify that the implement shutoff control is in the Unlocked position .
Move the control levers through the full range of travel several times. This should relieve any pressure that may be present in the implement hydraulic system.
Loosen the filler cap on the hydraulic tank so that the pressure in the tank is released. The machine may be equipped with a breaker valve. The breaker valve will be located on top of the tank. To release the pressure of the tank, press the button on top of the breaker valve (if equipped).
Tighten the filler cap on the hydraulic tank.
Make sure that the pressure in the entire hydraulic system has been released.
Turn the key to the OFF position.ReferenceRefer to Troubleshooting for additional guidance for preparing the machine for testing.Note: The monitoring system (if equipped) for your machine accesses many values that are useful in troubleshooting the power train system. When the situation is appropriate, use the monitoring system in order to find a pressure or determine a system problem.
Illustration 3 g02535054
Attach Tooling (A) or (B) to pressure tap (R2) .Test Procedure
Warm the transmission oil to operating temperature.
Run the engine at HIGH IDLE. Fully depress the brake pedal. Disengage the parking brake. Put the torque converter in a stalled condition with the transmission in 3.5 speed REVERSE. Note the pressure on the gauge. The pressure should be 410 50 kPa (60 7.5 psi). The engine RPM should be 1935 75 during the stalled condition.Note: This pressure pertains to a test that is done on the machine. The 410 50 kPa (60 7.5 psi) is not a bench test specification.
If the pressure that is observed is not 410 50 kPa (60 7.5 psi), perform the steps in "Adjustment Procedure".Adjustment Procedure
Shut off the engine.
Remove the torque converter outlet relief valve. The torque converter outlet relief valve is located at the back of the torque converter housing. Refer to Power Train Disassembly and Assembly, "Torque Converter Outlet Relief Valve - Remove" for your machine.
Table 3
SPACER CHART
Pressure Change To The Valve By Removal Or

Caterpillar SIS machinery equipment:

Caterpillar SIS
  • 901C Compact Wheel Loader W4T00001-UP (MACHINE) POWERED BY C1.8 Engine » 396-7742 STEP GP
  • 902C Compact Wheel Loader W5T00001-UP (MACHINE) POWERED BY C2.4 Engine » 396-7742 STEP GP
  • 903C Compact Wheel Loader W6T00001-UP (MACHINE) POWERED BY C2.4 Engine » 396-7742 STEP GP
  • 903C Compact Wheel Loader MW400001-UP (MACHINE) POWERED BY C2.4 Engine » 396-7742 STEP GP
  • 901C2 Compact Wheel Loader YKY00001-UP (MACHINE) POWERED BY C1.7 Engine » 396-7742 STEP GP
  • 902C2 Compact Wheel Loader YKT00001-UP (MACHINE) POWERED BY C2.4 Engine » 396-7742 STEP GP
  • 903C2 Compact Wheel Loader MW800001-UP (MACHINE) POWERED BY C2.4 Engine » 396-7742 STEP GP

Caterpillar parts catalog:

Caterpillar parts catalog
901C Compact Wheel Loader W4T00001-UP (MACHINE) POWERED BY C1.8 Engine
902C Compact Wheel Loader W5T00001-UP (MACHINE) POWERED BY C2.4 Engine
903C Compact Wheel Loader W6T00001-UP (MACHINE) POWERED BY C2.4 Engine
903C Compact Wheel Loader MW400001-UP (MACHINE) POWERED BY C2.4 Engine
901C2 Compact Wheel Loader YKY00001-UP (MACHINE) POWERED BY C1.7 Engine
902C2 Compact Wheel Loader YKT00001-UP (MACHINE) POWERED BY C2.4 Engine
903C2 Compact Wheel Loader MW800001-UP (MACHINE) POWERED BY C2.4 Engine


Parts step Caterpillar catalog:

2782072 STEP GP-TOOL BOX
M316D, M318D, M318D MH
1284231 STEP GP
330B L, 330C, 330C L
3805239 STEP GP
966M, 966M XE, 972M, 972M XE, 980M, 982M
2289922 STEP GP
525B, 535B, 535C, 545C
2892984 STEP GP
854G, 854K, 992G, 992K
1607555 STEP GP
854G, 854K, 992G
3671897 STEP GP
525D, 535D, 545D, 555D
2977547 STEP GP
345C, 345D, 345D L, 349D, 349D L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.