AVSPARE.COM
parts catalog

STRIP 1246044 - Caterpillar



1246044 STRIP Caterpillar parts 816F, 816F II STRIP
Rating:
42
Alternative (cross code) number:
CA1246044
124-6044
1246044
Caterpillar 1246044 STRIP
Weight: 0.74 pounds 0 kg.

Buy STRIP 1246044 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR,

Compatible equipment models: 1246044:

LANDFILL COMPACTOR  816F   816F II   Caterpillar
Number on catalog scheme: 11
 
  For full view, you need register

Information:


Illustration 1 g06344752
Table 1
Item Qty Part Specification Description
1 1 223-9159 Top Piston Ring Install the top piston ring with the side marked "UP-1" toward the top of the piston. The colored stripe faces to the right of the piston ring end gap.
Thickness of new top piston ring is 3.845 mm (0.1514 inch).
Clearance between the ends of the piston ring in a cylinder liner bore of 144.975 mm (5.7077 inch) is 0.40 0.10 mm (0.016 0.004 inch).
Increase in the clearance between the ends of the piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore is 0.08 mm (0.003 inch).
2 1 238-2707 Piston Ring Install the intermediate piston ring with the side marked "UP-2" toward the top of the piston. The colored stripe faces to the right of the piston ring end gap.
Thickness of new intermediate piston ring is 2.94 mm (0.116 inch).
Clearance between the ends of the piston ring in a cylinder liner bore of 144.975 mm (5.7077 inch) is 0.600 0.125 mm (0.0236 0.0049 inch).
Increase in the clearance between the ends of the piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore is 0.08 mm (0.003 inch).
3 1 246-5659 Piston Ring The spring ends of the oil control ring should be assembled 180 degrees from the ring end gap. The colored faces to the right or left of the piston ring end gap.
Width of groove in new piston for oil control piston ring is 3.020 0.010 mm (0.1189 0.0004 inch).
Thickness of new oil control piston ring is 2.980 0.010 mm (0.1173 0.0004 inch).
Clearance between the ends of the piston ring in a cylinder liner bore of 144.975 mm (5.7077 inch) is 0.55 0.15 mm (0.022 0.006 inch).
Increase in the clearance between the ends of the piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore is 0.08 mm (0.003 inch).
4 1 524-5565 Piston Pin Thoroughly lubricate the piston pin with clean engine oil before the piston is inserted into the piston body and the connecting rod.
Diameter of the bore in the finished bearing that is installed into the piston skirt for the piston pin is 60.125 0.005 mm (2.3671 0.00020 inch).
Diameter of the new piston pin is 59.975 0.005 mm (2.3612 0.0002 inch).
Length of the piston pin is 89.80 0.15 mm (3.535 0.006 inch).
Install the retainer ring (5) with the gap at the bottom of the piston. Refer to Illustration 1.
6 2 213-3217 Bolt Use the following procedure to tighten the rod bolts:
1.

Caterpillar parts catalog:

Caterpillar parts catalog
816F COMPACTOR 5FN00001-UP (MACHINE)
816F Landfill Compactor BMR00001-UP (MACHINE) POWERED BY 3176C Engine
816F Series 2 Landfill Compactor BZR00001-UP (MACHINE) POWERED BY C9 Engine


Parts strip Caterpillar catalog:

1H2629 STRIP-INSULATION
1090, 1190, 1190T, 120G, 120M, 120M 2, 1290T, 12E, 12G, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14E, 14G, 14H, 14M, 16, 160G, 160H, 160M, 160M 2, 160M ...
6W8946 STRIP AS
814F, 815F, 816F, 824C, 826C, 950F, 950F II, 960F, 966F, 966F II, 966G, 970F, 972G, 980C, 980F, 980F II
8R9250 STRIP
814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F
8R9564 STRIP
814F, 815F, 816F, 966F, 966F II, 970F
2W8744 STRIP
816F, D350E, D400E, D40D
2038040 STRIP
D7R, D7R II, D7R XR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.