parts catalog

STRIP 9V9228 - Caterpillar

9V9228 STRIP Caterpillar parts 824C, 980C, 980F, 980F II STRIP
Alternative (cross code) number:
Caterpillar 9V9228 STRIP
Weight: 4 pounds 1 kg.

Buy STRIP 9V9228 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 9V9228:

WHEEL LOADER  980C   980F   980F II   Caterpillar
Number on catalog scheme: 6
  For full view, you need register


Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter
C 364-9107 Timing Pin (Fuel Injection Pump) 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 1 g02482038
If necessary, use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center. Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check" for the correct procedure.
Use Tooling (B) in order to lock the crankshaft so that number one piston is at top dead center.
Use Tooling (C) in order to lock fuel injection pump (13) in the correct position. Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check" for the correct procedure.
If necessary, install studs (21) from front housing (20). Tighten the studs to a torque of 11 N m (97 lb in).
Position a new gasket (18) onto front housing (20).
Carefully install fuel injection pump (13) to front housing (20). Ensure that front housing (20) is not damaged as the fuel injection pump is installed. Note: The fuel injection pump should be supported by hand as the bolts are installed.
Install nuts (19) to fuel injection pump (13) finger tight.
Install new bolts (22) to fuel injection pump (13). Ensure that the different length bolts are installed in to the correct position.
Tighten bolts (22) to a torque of 22 N m (195 lb in). Tighten nut (19) to a torque of 22 N m (195 lb in).
Illustration 2 g02482036
Remove Tooling (C) from fuel injection pump (9). Install a new O-ring seal (7) (not shown) to plug (8).
Install plug (8) to fuel injection pump (9). Tighten the plug to a torque of 14 N m (124 lb in).
Remove the appropriate caps in order to install fuel injection line (1). Install a new fuel injection line (1) to the fuel injection pump and to the fuel manifold. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct procedure.
Position harness assembly (1) and bracket (5) onto the cylinder head. Loosely install bolt (4) and bolt (9) (not shown) to bracket (5).
Connected harness assembly (1) to coolant temperature sensor (2). Refer to Disassembly and Assembly, "Coolant Temperature Sensor - Remove and Install" for the correct procedure.
Install a new cable strap (3) to harness assembly

Caterpillar parts catalog:

Caterpillar parts catalog
980C Wheel Loader 63X06575-UP (MACHINE) POWERED BY 3406 Engine
980F Wheel Loader 8CJ00001-UP (MACHINE) POWERED BY 3406 Engine

Parts strip Caterpillar catalog:

1046217 STRIP
825C, 826C, 980C
824C, 825C, 826C, 980C
6W8276 STRIP
824C, 826C, 980C
814F, 815F, 816F, 824C, 826C, 950F, 950F II, 960F, 966F, 966F II, 966G, 970F, 972G, 980C, 980F, 980F II
7N3563 STRIP
824C, 826C, 980C
3V7483 STRIP
815B, 824C, 826C, 950B, 966D, 966F, 980C, 980F
3V7698 STRIP
814B, 815B, 816B, 824C, 826C, 950B, 950B/950E, 950F, 966D, 966F, 980C, 980F
4V7054 STRIP
980C, 980F, 980F II
4V4655 STRIP
824C, 826C, 980C
4V4576 STRIP
824C, 825C, 826C, 980C, 980F
6W0499 STRIP
824C, 826C, 980C, 980F, 980F II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.