AVSPARE.COM
parts catalog

SUPPORT, HARNESS 7095631C1 - Caterpillar



7095631C1 SUPPORT, HARNESS Caterpillar parts SUPPORT
Rating:
21
Alternative (cross code) number:
CA7095631C1
70956-31C1
7095631C1
Caterpillar 7095631C1 SUPPORT, HARNESS

Buy SUPPORT, HARNESS 7095631C1 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 5
 
  For full view, you need register

Information:

Note: SERVICE DATA: THE TOOLING IN TABLE 2 MAY NOT BE IDENTIFIED IN THE FOLLOWING PHOTOGRAPHS. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Illustration 9 g00943698
(A) Install bearing (1) . Install the bearing to depth (X) from the bottom face before installing lip seals (2) .Dimension (X) ... 7 0.5 mm (0.276 0.020 inch) (B) Install bearing (12) . The bearing must not extend beyond either face of the cylinder eye. (C) Apply Tooling (B) to the seal groove prior to the installation of the wiper seal (8) . Lubricate the lip of wiper seal (8) , seal (7) and wear ring (6) with the lubricant that is being sealed. (D) Lubricate the threads of self-locking nut (3) with Tooling (C) . Use a 65 mm socket for the removal and for the installation of the self-locking nut. The torque setting for the self-locking nut TH350B/TH360B (SLD1-Up/SLE1-Up) ... 1600 160 N m (1180 120 lb ft) (-) Lubricate the threads of self-locking nut (3) with Tooling (C) . Use a 65 mm socket for the removal and for the installation of the self-locking nut. The torque setting for the self-locking nut TH460B (SLF1-Up) ... 1200 120 N m (885 85 lb ft) (E) Lubricate piston seal (4) and wear ring (5) with the lubricant that is being sealed. (F) Lubricate O-ring seal (9) , the backup ring and O-ring seal (10) with the lubricant that is being sealed. (G) Lubricate the threads of head (11) with Tooling (C) . The torque setting for head (11) ... 600 130 N m (445 95 lb ft)Installation Procedure
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 10 g00926969
Apply a thin coat of 1U-6396 O-Ring Assembly Compound onto O-ring seals (13) before installing the seals in lock valve (2) .
Illustration 11 g00926968
Position lock valve (2) onto cylinder (5) and install four bolts (12) with the washers.
Illustration 12 g00935778
Attach a suitable nylon lifting sling around cylinder (5) and to a suitable hoist. Lift the cylinder toward the machine. The weight of the cylinder is approximately 38 kg (84 lb).Note: Make sure that lock valve (2) is facing downward.
Illustration 13 g00926967
Use the hoist to position cylinder (5) . Align the bore in the cylinder with bores in chassis (11) and install pin (10) , bolt (9) and the washer.
Illustration 14 g00926966
Use the hoist to position the rod end of cylinder (5) . Align the bore in the cylinder with bores in bracket (8) and install pin (7) , bolt (8) , the spacer and the washer. Remove the nylon lifting sling.
Illustration 15 g00926963
Connect harnesses (3) to solenoids (4) .
Illustration 16 g00926962
Connect three hoses (1) to lock valve (2) .
Illustration 17 g00926552
Remove the cribbing that was installed in the removal procedure between the chassis and the rear axle on both sides of the machine.

Caterpillar parts catalog:



Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.