parts catalog

SWITCH AS-ROCKER 1246240 - Caterpillar

1246240 SWITCH AS-ROCKER Caterpillar parts CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, PF-300C, PS-300B SWITCH
Alternative (cross code) number:
Caterpillar 1246240 SWITCH AS-ROCKER
Weight: 0.04 pounds 0 kg.

Buy SWITCH AS-ROCKER 1246240 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 1246240:

VIBRATORY COMPACTOR  CB-434B   CB-434C   CB-534B   CB-534C   CB-535B   CB-544   CB-545   Caterpillar
Number on catalog scheme: 2
  For full view, you need register


Table 3
Tool Item Qty Part
Number Description
B 198-4240 Digital Pressure Indicator Gp
B1 1 198-4234 Indicator
B2 1 198-4239 Pressure Sensor
34,450 kPa (5,000 psi)
B3 1 198-4236 Extension Cable
C 348-5430 Multi-Tool Gp
C1 1 285-0908 Multi-Tool
C2 1 6V-2198 Cable As
C3 1 9U-5140 Photo Pickup
C4 1 6V-3137 Base
C5 1 1U-6605 Reflective Tape
C6 1 6V-3138 Extension
D D1 1 6V-7788 Flow Meter
5 to 60 L/min (2 to 15 US gpm)
D2 1 8C-6874 Reducer
D3 1 6V-9746 O-Ring Seal
D4 1 124-1901 Permanent Coupling
D5 3 ft 122-6870 Bulk Hydraulic Hose
D6 1 124-2147 Permanent Coupling
D7 1 6V-8942 O-Ring Reducer
D8 1 6V-8556 Nut
D9 1 6V-8398 O-Ring Seal
F 1 311-1362 Vacuum Cap Reference: Refer to Tool Operating Manual, NEHS1087 for operating instructions for the 348-5430 Multi-Tool Gp.Note: Use Software License Card, NETG5049 with part number 348-5430 Multi-Tool Gp.Machine Preparation
To prevent personal injury or equipment damage from failure of the hydraulic test equipment or associated circuit components because of blocked pump flow, make sure that the test equipment valves are fully open before starting the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Note: Set the pilot relief valve to the specification. Refer to Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust".
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Attach 311-1362 Vacuum Cap (F) onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 4 g03883789
Flow meter tool layout
Tooling (D)
( 1) Hose
(2) Pilot filter
(3) Elbow
(4) Pilot pump
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 4.
Disconnect hose (1) from elbow (3).
Connect flow meter assembly (D) between elbow (3) and hose (1). Note: Correct orientation of the flow meter is necessary. The oil flows from pilot pump (4) to pilot filter (2).
Remove 311-1362 Vacuum Cap.
Install tooling (C) on the engine to monitor engine speed. Test Procedure
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Check the flow of oil through the flow meter. Refer to Table 1.

Caterpillar parts catalog:

Caterpillar parts catalog
CB-534B Vibratory Compactor 5RN00001-UP (MACHINE) POWERED BY 3054 Engine
PS-300B PF-300B Pneumatic Compactor 4PN00001-00525 (MACHINE) POWERED BY 3054 Engine
CB-434B Vibratory Compactor 7YN00001-UP (MACHINE) POWERED BY 3054 Engine
CB-544 Vibratory Compactor 8FM00001-UP (MACHINE) POWERED BY 3054 Engine
CB-535B Vibratory Compactor 3AR00001-UP (MACHINE) POWERED BY 3054 Engine
CB-545 Vibratory Compactor 2FS00001-UP (MACHINE) POWERED BY 3054 Engine
CB-534C Vibratory Compactor 1WS00001-UP (MACHINE) POWERED BY 3054 Engine
CB-434C Vibratory Compactor 4MW00001-UP (MACHINE) POWERED BY 3054 Engine
PS-300B PF-300B Pneumatic Compactor 4PN00526-UP (MACHINE) POWERED BY 3054 Engine
PF-300C,PS-300C Pneumatic Compactor PFB00001-UP (MACHINE) POWERED BY 3054C Engine

Parts switch Caterpillar catalog:

0814194 SWITCH
CB-214B, CB-224C
CB-224C, CB-434B, CB-434C, CB-534, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CB-634C, CP-433C, CP-433E, CS-423E, CS-431C, PF-290B, PS-150B, PS-200B, PS-300B, PS-360B
1068780 SWITCH
CB-224C, CB-434, CB-434B, CB-534B
CB-434, PF-300C, PS-300B
CB-434, CB-434B, CB-534, CB-534B, CB-535B, CB-544, CB-545, CB-634
CB-434C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.