AVSPARE.COM
parts catalog

SWITCH-MICRO 4644973 - Caterpillar



4644973 SWITCH-MICRO Caterpillar parts SWITCH
Rating:
46
Alternative (cross code) number:
CA4644973
464-4973
4644973
Caterpillar 4644973 SWITCH-MICRO
Weight: 0.02 pounds 0 kg.

Buy SWITCH-MICRO 4644973 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01321409
Schematic of the Cab Ventilation Duct Temperature SensorThis diagnostic code is associated with the Cab Ventilation Duct Temperature sensor. This diagnostic code is recorded when the ECM reads the signal from the sensor (wire G933-YL) as being shorted to +battery. The signal (wire G933-YL) connects to contact J1-53 of the ECM.Possible causes of the diagnostic code is listed:
The return circuit is open.
The signal circuit is open or the sensor is disconnected.
The signal circuit is shorted to +battery.
The sensor has failed.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.System Response:A level 1 warning will be generated.Note: Ensure that CID 2663 FMI 03 is active. This procedure can cause new diagnostic codes to be recorded. Ignore these created diagnostic codes. When the procedure is completed, clear the created diagnostic codes.Test Step 1. CHECK FOR AN OPEN IN THE RETURN CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
The sensor remains disconnected from the machine harness.
Disconnect the machine harness connector J1 from the ECM.
At the machine harness connector for the sensor, measure the resistance from contact 2 (wire J767-GY) to ground.Expected Result:The resistance measurement should measure less than 5 ohms.Results:
OK - The resistance measurement is less than 5 ohms. The harness is correct. Proceed to Test Step 2.
NOT OK - The resistance that is measured is not correct.Repair: There is an open in the machine harness. The open is in the return circuit with the high resistance measurement. Repair the harness or replace the harness.STOPTest Step 2. CHECK FOR AN OPEN IN THE SIGNAL CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the machine harness connector for the sensor, install a jumper wire from contact 1 (wire G933-YL) to contact 2 (wire J767-GY).
At the machine harness connector J1, measure the resistance from contact J1-53 (wire G933-YL) to Frame Ground.Expected Result:The resistance should measure less than 5 ohms.Results:
OK - The resistance measures less than 5 ohms. Proceed to 3.
NOT OK - The resistance measurement is greater than 5 ohms.Repair: There is an open in the signal circuit. Repair the harness or replace the harness.STOPTest Step 3. CHECK THE SIGNAL CIRCUIT FOR A SHORT.
The disconnect switch and the key start switch remain in the OFF position.
The machine harness connectors J1 and J2 remain disconnected.
Remove the jumper wire from contact 1 (wire G933-YL) to contact 2 (wire J767-GY).
At the J1 and J2 machine harness connectors for the ECM, measure the resistance for the signal contact of the sensor J1-53 (wire G933-YL) to all other J1 and J2 contacts.Expected Result:Each resistance measurement should


Parts switch Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.