AVSPARE.COM
parts catalog

TANK GP-FUEL 1694662 - Caterpillar



1694662 TANK GP-FUEL Caterpillar parts 550, 550B, 560B, 570, 570B, 580, 580B TANK
Rating:
40
Alternative (cross code) number:
CA1694662
169-4662
1694662
Caterpillar 1694662 TANK GP-FUEL

Buy TANK GP-FUEL 1694662 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL HARVESTER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop | Key for Simplicity 518H 1694660, 1694662, 1694750, 2690327, 2690328, 2690329
$7.49

31 May 2022

US: The ROP Shop
The ROP Shop | Key for Simplicity 518H 1694660, 1694662, 1694750, 2690327, 2690328, 2690329
The ROP Shop The ROP Shop replacement Key for Simplicity 518H 1694660, 1694662, 1694750, 2690327, 2690328, 2690329 || Specs - Refer to image 2 for more information || Includes - (1) Ignition Key; comes as shown in the first image || Please be sure to check your part or model number to ensure this is the correct ignition key for your unit. Also, please note this may replace multiple parts numbers
Number on catalog scheme: 7
 
  For full view, you need register

Compatible equipment models: 1694662:

WHEEL HARVESTER  550   550B   560B   570   570B   580   580B   Caterpillar

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8221 Lifting Sling 1 Start By:
Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove and Install".
If the crankshaft has been reground or if the crankshaft has been replaced, the height of the piston above the cylinder block must be inspected. It is necessary to remove the cylinder head in order to inspect the height of the piston above the cylinder block.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
If necessary, remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove". Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove". If the cylinder head, the pistons and the connecting rods have not been removed, remove the connecting rod caps. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Remove".
Illustration 1 g01439628
Typical example
Remove allen head screws (1). Remove bridge piece (2).
Ensure that the main bearing caps are marked for the location and orientation.
Illustration 2 g01253719
Typical example
Remove bolts (3) and main bearing caps (4) from the cylinder block.
Illustration 3 g01253146
Typical example
Illustration 4 g01253137
Typical example
Remove lower main bearings (5) from main bearing caps (4). Take care not to displace dowels (6). For number three main bearing cap, remove thrust washers (7). Keep the lower main bearings and the thrust washers with the respective main bearing caps. Note: The lower main bearings are plain bearings that have no oil holes. The dowels may remain in the main bearing cap or in the cylinder block.
Illustration 5 g01254099
Typical example
Attach Tooling (A) and a suitable lifting device to crankshaft (8). Carefully lift the crankshaft out of the cylinder block. The weight of the crankshaft is approximately 30 kg (66 lb). Note: Do not damage any of the finished surfaces on the crankshaft. When the crankshaft is removed from the engine, the crankshaft must be supported on a suitable stand in order to prevent damage to the crankshaft timing ring.
Illustration 6 g01254104
Typical example
Illustration 7 g01889993
No. 1 Upper Main Bearing
Remove upper main bearings (9) from the cylinder block. Keep the upper main bearings with the respective main bearing caps. Note: Number 1 upper main bearing has an oil slot. See Illustration 7. All other upper main bearings have a groove and two oil holes.
Remove thrust washers (10) from number three main bearing in the cylinder block.
If necessary, remove the crankshaft timing ring. Refer to Disassembly and Assembly, "Crankshaft Timing Ring - Remove and Install".
If necessary, remove the crankshaft

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
550 Wheel Harvester 7ZN00001-UP (MACHINE) POWERED BY 3126 Engine
570 Wheel Harvester 4XR00001-UP (MACHINE) POWERED BY 3126 Engine
580 Wheel Harvester 7CN00001-UP (MACHINE) POWERED BY 3126 Engine
570B Harvester CKG00001-UP (MACHINE) POWERED BY 3126B Engine
580B Wheel Harvester CLT00001-UP (MACHINE) POWERED BY 3126B Engine
550B WHEEL HARVESTER SAW00001-UP (MACHINE) POWERED BY 3056E Engine
560B WHEEL HARVESTER TRA00001-UP (MACHINE) POWERED BY 3056E Engine


Parts tank Caterpillar catalog:

1694663 TANK GP-HYDRAULIC
550, 550B, 560B, 570, 570B, 580, 580B
1595586 TANK GP-HYDRAULIC
550, 550B, 560B, 570, 570B, 580, 580B
1593669 TANK & MTG GP-HYDRAULIC
550, 550B, 560B, 570, 570B, 580, 580B
2304097 TANK GP-FUEL
550B, 560B, 570B, 580B
1590723 TANK GP-FUEL
550, 570, 570B, 580, 580B
1625872 TANK
550, 550B, 560B, 570, 570B, 580, 580B
1640064 TANK AS
550, 550B, 560B, 570, 570B, 580, 580B
1595578 TANK AS
550, 550B, 560B, 570, 570B, 580, 580B
1569091 TANK AS
550, 550B, 560B, 570, 570B, 580, 580B
1752534 TANK
550, 550B, 560B, 570, 570B, 580, 580B
1615152 TANK
550, 550B, 560B, 570, 570B, 580, 580B
1985081 TANK-EXPANSION
550B, 560B, 570B, 580B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.