AVSPARE.COM
parts catalog

TANK GP-WATER 3534733 - Caterpillar



3534733 TANK GP-WATER Caterpillar parts D9T TANK
Rating:
85
Alternative (cross code) number:
CA3534733
353-4733
3534733
Caterpillar 3534733 TANK GP-WATER

Buy TANK GP-WATER 3534733 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 3534733:

TRACK-TYPE TRACTOR  D9T   Caterpillar
Number on catalog scheme:
  
  For full view, you need register

Information:

1. Loosen set screw (2), and remove handle (1) from the shift lever. Remove four screws (3). 2. Lift up cover to access hoses, and disconnect two hoses (4) to the parking brake control. Cap and plug all connections. 3. Disconnect lamp (5), and remove cover (6). 4. Remove four screws (8). Remove cover (7). 5. Remove two screws (9). Reposition electronic sensor (10). 6. Remove two bolts (12) and the washers. Remove shift handle (11). 7. Remove three nuts (13) and the washers. Remove transmission control assembly (14). The following steps are for the installation of the transmission control. 8. Install transmission control assembly (14) with three nuts (13) and washers. Do not tighten nuts (13) at this time. 9. Install shift lever (11). With shift lever (11) in the FOURTH speed position, timing marks (15) must be in alignment. 10. Connect lamp (5) to cover (6). 11. Connect two hoses (4) to the parking brake control, and install the cover. 12. Move shift lever (11) to the end of slot at REVERSE position. Use a depth gauge to adjust the position of the lever to get a distance of 1.0 mm (.04 in) between lever (11) and the corner of the switch case. 13. Tighten three nuts (13) once shift lever adjustment is correct. 14. Install sensor (10) and screws (9). 15. Install cover (7) and four screws (8). 16. Install handle (1) and tighten set screw (2).17. Start the machine to recharge the air reservoirs.Disassemble & Assemble Transmission Control
Start by:a. remove transmission control 1. Remove four plugs (5) with O-rings, springs (4), pins (3) and balls (2) from housing (1). 2. Using Tool (A) and a suitable press, remove shaft (7) and two sleeve bearings (6) from housing (1). The following steps are for the assembly of the transmission control. 3. Using Tool (A) and a suitable press, install sleeve bearing (6) on switch side of housing. 4. Using Tool (A) and a suitable press, install shaft (7) and other sleeve bearing (6). 5. Check the condition of the O-rings on the plugs (5) and replace if necessary. Fill cavities (8) with 1P-0808 Lubricant. Install balls (2), pins (3), springs (4) and plugs (5) with O-rings.End by:a. install transmission control

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
DV232 Track Type Tractor NJH00001-UP (MACHINE) POWERED BY C18 Engine
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) POWERED BY C18 Engine


Parts tank Caterpillar catalog:

9U9409 TANK
572R, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D7H, D7R, D7R II, D7R XR, D8N, D8T, D9N, D9R, D9T
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.