AVSPARE.COM
parts catalog

TANK & FILTER GP-HYDRAULIC 4Z6472 - Caterpillar



4Z6472 TANK & FILTER GP-HYDRAULIC Caterpillar parts 950G, 950G II, 962G, 962G II, IT62G II TANK
Rating:
82
Alternative (cross code) number:
CA4Z6472
4Z-6472
4Z6472
Caterpillar 4Z6472 TANK & FILTER GP-HYDRAULIC
Weight: 0.45 pounds 0 kg.

Buy TANK & FILTER GP-HYDRAULIC 4Z6472 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 4Z6472:

INTEGRATED TOOLCARRIER  IT62G II  
WHEEL LOADER  950G   950G II   962G   962G II   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7600     Slide Hammer Puller     1    
B (1)     5P-7314     Distorter Ring     1    
C (1)     5P-7312     Seal Distorter     1    
( 1 ) Part of the 5P-7318 Wear Sleeve Distorter Group Start By:
Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The front seal and the wear sleeve must be replaced at the same time. Once the seal and the wear sleeve are separated, these components can not be used again. Refer to Special Instruction, SMHS8508, "Special Handling Information and Installation Instructions for Crankshaft Seal Groups That Have Hydrodynamic Grooves In the Sealing Lip" before the seal is serviced.
Illustration 1 g00829187
(1) Seal (2) Wear sleeve
Illustration 2 g00582156
Typical example
Use a punch or Tooling (A) in order to puncture a hole in seal (1) .
Use Tooling (A) in order to remove seal (1) .
Illustration 3 g00582158
Typical example
Place Tooling (B) into position.Note: The correct position is shown in Illustration 3.
Install Tooling (C) between Tooling (B) and the wear sleeve.
Turn Tooling (C), until the edge of the tool makes a flat crease in the wear sleeve. Repeat this procedure until there are enough creases in the wear sleeve in order to allow the wear sleeve to be slipped off the end of the crankshaft.
Remove Tooling (B) and the wear sleeve by hand.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
IT62G II Integrated Toolcarrier AYA00001-UP (MACHINE) POWERED BY 3126B Engine
2Z-9989 Waste Handler Custom Product Support Literature for 950G Wheel Loader 3JW00001-UP (MACHINE)
4W-1794 WASTE AR CUSTOM PRODUCT SUPPORT LITERATAURE FOR 950G 2JS00001-UP (MACHINE)
179-5364 Trash Ar Custom Product Support Literature for 962G Wheel Loader 3BS00001-UP (MACHINE)
Waste Handler Custom Product Support Literature for the 950G Series II Wheel Loader and the 962G Series II Wheel Loader AYB00001-UP (MACHINE)
962G II Wheel Loader BAD00001-UP (MACHINE) POWERED BY 3126B Engine
950G II WHEEL LOADER BAA00001-UP (MACHINE) POWERED BY 3126B Engine
950G II Wheel Loader AXR00001-UP (MACHINE) POWERED BY 3126B Engine
950G II Wheel Loader AXX00001-UP (MACHINE) POWERED BY 3126B Engine
962G II Wheel Loader AXY00001-UP (MACHINE) POWERED BY 3126B Engine
962G II Wheel Loader AXS00001-UP (MACHINE) POWERED BY 3126B Engine


Parts tank Caterpillar catalog:

2489374 TANK GP-FUEL
345C, 345C MH, W345C MH
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.