parts catalog

TIE WRAPS 0003886 - Caterpillar

0003886 TIE WRAPS Caterpillar parts WE-601B TIE
Alternative (cross code) number:
Caterpillar 0003886 TIE WRAPS

Buy TIE WRAPS 0003886 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 0003886:

WINDROW ELEVATOR  WE-601B   Caterpillar
Number on catalog scheme:
  For full view, you need register


Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 504-9791 Lift Gp (60Hz)(1) 1
504-9793 Lift Gp (50Hz)(2) 1
B 439-3940 Bracket As 1
(1) High-Voltage (480V) Low-Voltage (240V)
(2) High-Voltage (400V) Low-Voltage (200V)
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed.Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death.Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all hoses and on all hose assemblies for installation purposes. Plug all hose assemblies to prevent fluid loss, and to prevent contaminants from entering the system.
Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering Frame Lock".
Illustration 1 g06287257
Position drawbar (1) to the left side of the machine. Position the blade onto suitable cribbing. Support the circle with Tooling (A) as shown. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A).
Stop the engine. Release the system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Illustration 2 g01403317
Attach Tooling (B) and a suitable lifting device to swivel (3). The weight of swivel (3) is approximately 41 kg (90 lb).
Disconnect hose assemblies (2), (5), and (6).
Remove bolts (7) and lower swivel (3).
Remove the suitable lifting device.
Remove all clamps (4) that connect hose assemblies (6) to the drawbar.
Illustration 3 g01403392
Remove centershift cylinder (8). Refer to Disassembly and Assembly, "Centershift Cylinder - Remove and Install".
Remove bolts (10), cap (9), and the shims. Repeat this step for the opposite side of the machine.Note: Note the number and the location of the shims.
Use the hydraulics to retract the blade lift cylinders.Note: Secure the blade lift cylinders to the front frame.
Illustration 4 g01403404
Loosen nuts (11).
Loosen set screws (12).
Remove bolts (13).
Remove shoe (14) and wear strip (15).Note: Note the location of the shoes.
Repeat Steps

Caterpillar parts catalog:

Caterpillar parts catalog

Parts tie Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.